Demon Phat - Step by Step Installation Guide

Ubergeek

Xecuter Groupie
Feb 24, 2003
6,272
0
California, USA
Make sure you read these instructions first: http://www.team-xecuter.com/forums/showthread.php?t=88214

These are the QSB & Wire solder points for all Phat Models

There is also an optional SYNC Connection (Brown Wire) and Remote Power Connection (Orange Wire).

Note: Ignore the CoolRunner install wires - the pictures were taken with an RGH1 install by mistake - we know there is no PLL_BYPASS with RGH2 - Click here For CoolRunner Phat RGH2 Install ;)

Recommended Installation Equipment:

Hakko FX-888 Soldering Station - $79.95




Xecuter XBOX 360 Unlock Kit v3 - $9.95




Xecuter Fiberglass Scratch Brush - $4.95



GC Electronics Liquid Solder Flux - 2 oz Bottle - $8.95









Will add comments later....work in progress.....















If you are using a CoolRunner Rev A / Rev B - Click HERE for the CR_EN Instructions. You will also find the updated XSVF files for your Xecuter CoolRunner (Rev A, B & C)









































Any questions ?
 

badwigga

VIP Member
Nov 15, 2009
498
0
AUSTRALIA
Re: Demon Phat Install Diagram

cant wait 1 slim 1 phat thanks uber. :)
 

NeoGodSpeed

VIP Member
Mar 14, 2007
150
0
Arizona
Re: Demon Phat Install Diagram

C2R6 = Black (Ground)

Only Question as it looks very nice & simple, well done

Thank You.
 

Netkar

VIP Member
Apr 27, 2005
391
33
Re: Demon Phat Install Diagram

so is right no solder the quick solder point below the green point on demon?
is the same of green point right?
 
Last edited:

Ubergeek

Xecuter Groupie
Feb 24, 2003
6,272
0
California, USA
Re: Demon Phat Install Diagram

Just one quick question.....Where would one go about soldering the sync and remote power connection?
In the places we tell you to when the instructions have been uploaded :p

---------- Post added at 11:42 ---------- Previous post was at 11:42 ----------

so is right no solder the quick solder point below the green point on demon?
I have no idea what this means :confused:
 
  • Like
Reactions: keil423

Netkar

VIP Member
Apr 27, 2005
391
33
Re: Demon Phat Install Diagram

I have no idea what this means :confused:
Sorry I've see one quick solder point on demon without the purple dot now I have see is an alt of green dot.

Forgive my stupid mind
 

Ubergeek

Xecuter Groupie
Feb 24, 2003
6,272
0
California, USA
Re: Demon Phat Install Diagram

Looks easy enough :D

Just a quick question, Where does the CoolRunner connected to this at all or does it not need to??
you will see when the install guides are uploaded :)

---------- Post added at 12:00 ---------- Previous post was at 11:59 ----------

Just one quick question.....Where would one go about soldering the sync and remote power connection?
the brown is sync the orange is remote power - ill obviously have much better guides posted later but this should give you an idea :)

 
  • Like
Reactions: idle_kers
Re: Demon Phat Install Diagram

is the small board with en, for coolrunners that are rev a and b, as the rev c has the en on it?
and that coolrunner en links to the demon cr-en points, so that the cr can be shut down via the demon for onboard nand to be used and no attempted glitching!
 
Last edited: