Jasper CB 6754 256 BB with RJTAG installed
Demon installed with BB upgrade kit
Stock dash is on 16203
hacked dash is RJTAG image with Aud clamp enabled
OK. I installed RJTAG on a Jasper 256 BB and got it glitching properly with dips 3, 7, and 8 and a pro rater average score of 2. I then proceeded to install a demon (Small Block) with the BB upgrade kit soldered on with wires as I could not install it normally due to the AUD clamp QSB's position on the motherboard. The install went through successfully and I'm pretty confident in my soldering job. I do have some bad blocks on my original dump which were remapped and I'm thinking this is where the trouble may lie. I have tried using the "noremap" checkbox in advanced Xebuild options to no avail and I'm quite confused about the whole remapped / unremapped blocks and what needs to be where when writing a NAND to the demon. When I tried to write to the demon with noremap enabled I was getting invalid block errors when trying to write. With noremap disabled it will write to the demon fine but it still will not boot...The issue is that it doesn't try to turn on at all, no power, nothing on the ROL board whatsoever. PLEASE NOTE: This is a demon that I removed from a problematic falcon which also refused to boot, but I did remove the demon completely from that system and it still failed to boot. I came to the conclusion that I blew a mosfet by shorting components under the motherboard from metal whiskers on my work bench. I have since started using clean sheets of cardboard. But this demon was installed to that Xbox when the suspected short occured so please keep that in mind; although the demon is switching properly and is fully readable / writable in both Jrunner and Demon Toolbox. The system DOES boot up properly from the stock NAND.
Sorry for the long log I know there's a site you're supposed to use to post logs but I'm not sure what it is so if someone could tell me that as well I would appreciate it.
Jrunner log:
I have also tried flashing the stock NAND to the demon, both unmapped and remapped to no avail, still no power.
please help!
.
Demon installed with BB upgrade kit
Stock dash is on 16203
hacked dash is RJTAG image with Aud clamp enabled
OK. I installed RJTAG on a Jasper 256 BB and got it glitching properly with dips 3, 7, and 8 and a pro rater average score of 2. I then proceeded to install a demon (Small Block) with the BB upgrade kit soldered on with wires as I could not install it normally due to the AUD clamp QSB's position on the motherboard. The install went through successfully and I'm pretty confident in my soldering job. I do have some bad blocks on my original dump which were remapped and I'm thinking this is where the trouble may lie. I have tried using the "noremap" checkbox in advanced Xebuild options to no avail and I'm quite confused about the whole remapped / unremapped blocks and what needs to be where when writing a NAND to the demon. When I tried to write to the demon with noremap enabled I was getting invalid block errors when trying to write. With noremap disabled it will write to the demon fine but it still will not boot...The issue is that it doesn't try to turn on at all, no power, nothing on the ROL board whatsoever. PLEASE NOTE: This is a demon that I removed from a problematic falcon which also refused to boot, but I did remove the demon completely from that system and it still failed to boot. I came to the conclusion that I blew a mosfet by shorting components under the motherboard from metal whiskers on my work bench. I have since started using clean sheets of cardboard. But this demon was installed to that Xbox when the suspected short occured so please keep that in mind; although the demon is switching properly and is fully readable / writable in both Jrunner and Demon Toolbox. The system DOES boot up properly from the stock NAND.
Sorry for the long log I know there's a site you're supposed to use to post logs but I'm not sure what it is so if someone could tell me that as well I would appreciate it.
Jrunner log:
Code:
===================================================
Friday, July 12, 2013 9:47:33 PM
J-Runner v0.2 Beta (289) Started
Checking Files
Initializing nanddump1.bin..
CpuKey is Correct
Key already Exists
Nand Initialization Finished
Current: XBOX
Switching to DemoN
Success
Finished Checking Files
Current: DemoN
Switching to XBOX
Success
XBOX360
Hardware : Demon Phat
Firmware : 1.4
Flash ID : 0xDAAD Hynix (256MiB - Big block)
Flash Size : 0x800 blocks of 0x21000 bytes
Invalid Blocks : 0x1D9
Writing Nand
Done!
in 1:17 min:sec
Load Files Initiliazation Finished
Clean SMC detected
Patching Jasper version 2.3 SMC at offset 0x12BA
16203
Started Creation of the 16203 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.07.561
---------------------------------------------------------------
building jtag image
**************** WARNING *************************
nanddump.bin has NAND memory unit data, make
sure you back up any important data off the
internal MU before flashing a new image!
****************************************************
******* WARNING: could not patch SMC reset limit!
---------------------------------------------------------------
D:\Users\Brian\Downloads\J-Runner v02 (271) Core Pack\J-Runner v02 (271) Core Pack\051809584607\updflash.bin image built, info:
---------------------------------------------------------------
Console : Jasper (big block)
NAND size : 64MiB + NAND MU area
Build : JTAG
Xell : power on console with console eject button
Serial : 051809584607
ConsoleId : 030054044235
MoboSerial: 8921731212448467
Mfg Date : 11/12/2008
CPU Key : E49300DEE22258DEDDB5D30C8DAF186D
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : 23F421A701FBB721E111320D8F8C00C5
CF LDV : 4
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to D:\Users\Brian\Downloads\J-Runner v02 (271) Core Pack\J-Runner v02 (271) Core Pack\051809584607
Image is Ready
Current: XBOX
Switching to DemoN
Success
DemoN
Hardware : Demon Phat
Firmware : 1.4
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks : 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39
Writing Nand
Options.ini file was altered successfully
Starting remapping process
Remapping Block 0x0 @ 0x3FF
Remapping Block 0x1 @ 0x3FE
Remapping Block 0x2 @ 0x3FD
Remapping Block 0x3 @ 0x3FC
Remapping Block 0x4 @ 0x3FB
Remapping Block 0x5 @ 0x3FA
Remapping Block 0x6 @ 0x3F9
Remapping Block 0x7 @ 0x3F8
Remapping Block 0x8 @ 0x3F7
Remapping Block 0x9 @ 0x3F6
Remapping Block 0xA @ 0x3F5
Remapping Block 0xB @ 0x3F4
Remapping Block 0xC @ 0x3F3
Remapping Block 0xD @ 0x3F2
Remapping Block 0xE @ 0x3F1
Remapping Block 0xF @ 0x3F0
Remapping Block 0x10 @ 0x3EF
Remapping Block 0x11 @ 0x3EE
Remapping Block 0x12 @ 0x3ED
Remapping Block 0x13 @ 0x3EC
Remapping Block 0x14 @ 0x3EB
Remapping Block 0x15 @ 0x3EA
Remapping Block 0x16 @ 0x3E9
Remapping Block 0x17 @ 0x3E8
Remapping Block 0x18 @ 0x3E7
Remapping Block 0x19 @ 0x3E6
Remapping Block 0x1A @ 0x3E5
Remapping Block 0x1B @ 0x3E4
Remapping Block 0x1C @ 0x3E3
Remapping Block 0x1D @ 0x3E2
Remapping Block 0x1E @ 0x3E1
Remapping Block 0x1F @ 0x3E0
Remapping Block 0x20 @ 0x3DF
Remapping Block 0x21 @ 0x3DE
Remapping Block 0x22 @ 0x3DD
Remapping Block 0x23 @ 0x3DC
Remapping Block 0x24 @ 0x3DB
Remapping Block 0x25 @ 0x3DA
Remapping Block 0x26 @ 0x3D9
Remapping Block 0x27 @ 0x3D8
Remapping Block 0x28 @ 0x3D7
Remapping Block 0x29 @ 0x3D6
Remapping Block 0x2A @ 0x3D5
Remapping Block 0x2B @ 0x3D4
Remapping Block 0x2C @ 0x3D3
Remapping Block 0x2D @ 0x3D2
Remapping Block 0x2E @ 0x3D1
Remapping Block 0x2F @ 0x3D0
Remapping Block 0x30 @ 0x3CF
Remapping Block 0x31 @ 0x3CE
Remapping Block 0x32 @ 0x3CD
Remapping Block 0x33 @ 0x3CC
Remapping Block 0x34 @ 0x3CB
Remapping Block 0x35 @ 0x3CA
Remapping Block 0x36 @ 0x3C9
Remapping Block 0x37 @ 0x3C8
Remapping Block 0x38 @ 0x3C7
Remapping Block 0x39 @ 0x3C6
Done!
in 0:40 min:sec
Initializing nanddump1.bin..
CpuKey is Correct
Key already Exists
Using edited settings
Load Files Initiliazation Finished
Clean SMC detected
Patching Jasper version 2.3 SMC at offset 0x12BA
16203
Started Creation of the 16203 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.07.561
---------------------------------------------------------------
building jtag image
**************** WARNING *************************
nanddump.bin has NAND memory unit data, make
sure you back up any important data off the
internal MU before flashing a new image!
****************************************************
******* WARNING: could not patch SMC reset limit!
---------------------------------------------------------------
D:\Users\Brian\Downloads\J-Runner v02 (271) Core Pack\J-Runner v02 (271) Core Pack\051809584607\updflash.bin image built, info:
---------------------------------------------------------------
Console : Jasper (big block)
NAND size : 64MiB + NAND MU area
Build : JTAG
Xell : power on console with console eject button
Serial : 051809584607
ConsoleId : 030054044235
MoboSerial: 8921731212448467
Mfg Date : 11/12/2008
CPU Key : E49300DEE22258DEDDB5D30C8DAF186D
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : 23F421A701FBB721E111320D8F8C00C5
CF LDV : 4
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to D:\Users\Brian\Downloads\J-Runner v02 (271) Core Pack\J-Runner v02 (271) Core Pack\051809584607
Image is Ready
Nand Initialization Finished
DemoN
Hardware : Demon Phat
Firmware : 1.4
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Invalid Blocks :
Writing Nand
Starting remapping process
Done!
in 0:32 min:secI have also tried flashing the stock NAND to the demon, both unmapped and remapped to no avail, still no power.
please help!
.
Last edited by a moderator:
