DemoN Trinity Booting RDot

[ScrubbaDubby]

(ANSWERED) DemoN Trinity Booting RDot

KEEP CHECKING SOLDER POINTS, THE EXTERNAL USB's RIBBON WAS PLUGGED IN BELOW THE CONNECTORS

Credit to: Martin C and BlaK3y In this thread and previous threads pertaining to this install



-DemoN is not lighting up, ever. Set to XB or PC and plugged into PC or PSU or if xbox is on
-Same with the external USB (Computer doesn't read external usb either)

-Coolrunner Rev B installed and hooked up to DemoN along with CR_EN alternative point for rev b and a

-Can't switch NAND on xbox, it always boots the DemoN NAND (RGH'd NAND)

-Goes straight to Red Dot after the coolrunner has glitched it

-I have Xbox NAND written to it's original Retail

-Xbox boots fine when NAND's are written to Retail

Soldering Pics
https://www.dropbox.com/sh/09igr8j4nafc741/skdMenBw9D

Jrunner Log:
===================================================
Sunday, August 26, 2012 12:04:24 PM

J-Runner v0.2 Beta (279) Started



Checking Files
Finished Checking Files
Initializing Nand..
Nand Initialization Finished
* unpacking flash image, ....
ECC'ed - will unecc.
UnECC'ed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 3.1
CB_A: 9230
CB_B: 9230
CD (image): 9230
CD (decrypted): 9452
* checking required versions...
ok
* patching SMC...
Patching Trinity version 3.1 SMC at offset 0x13B3
* Replacing CD...

* Building new bootloader chain using cpu_key: 229265901E805F794ED839FBED913A85
* encrypting CB...
* constructing new image...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x9ABF (0x1AC0 bytes) CB_A 9188
0x9AC0..0x112BF (0x7800 bytes) CB_B 9188
0x112C0..0x172BF (0x6000 bytes) CD 9452
0x172C0..0xBFFFF (0xA8D40 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...Done!
------------- Written into output\image_00000000.ecc

Device Not Found.
Initializing Nand..
Nand Initialization Finished
* unpacking flash image, ....
ECC'ed - will unecc.
UnECC'ed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 3.1
CB_A: 9230
CB_B: 9230
CD (image): 9230
CD (decrypted): 9452
* checking required versions...
ok
* patching SMC...
Patching Trinity version 3.1 SMC at offset 0x13B3
* Replacing CD...

* Building new bootloader chain using cpu_key: 229265901E805F794ED839FBED913A85
* encrypting CB...
* constructing new image...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x9ABF (0x1AC0 bytes) CB_A 9188
0x9AC0..0x112BF (0x7800 bytes) CB_B 9188
0x112C0..0x172BF (0x6000 bytes) CD 9452
0x172C0..0xBFFFF (0xA8D40 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...Done!
------------- Written into output\image_00000000.ecc

Initializing Nand..
Nand Initialization Finished
DEMON
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Writing Nand
Done!
in 0:26 min:sec

* unpacking flash image, ....
ECC'ed - will unecc.
UnECC'ed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 3.1
CB_A: 9230
CB_B: 9230
CD (image): 9230
CD (decrypted): 9452
* checking required versions...
ok
* patching SMC...
Patching Trinity version 3.1 SMC at offset 0x13B3
* Replacing CD...

* XOR HACK NEEDED FOR CB 9230
* patching CB_B...
patchset for 9188 found, 4 patch(es)
* Applying XOR Hack to CB_B 9230
*** Re-encrypting CB_B with xor keystream
*** Fixing entrypoint
* Replacing CB_A 9230 with 9188
* encrypting CB...
* constructing new image...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x9ABF (0x1AC0 bytes) CB_A 9188
0x9AC0..0x114EF (0x7A30 bytes) CB_B 9188
0x114F0..0x174EF (0x6000 bytes) CD 9452
0x174F0..0xBFFFF (0xA8B10 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...Done!
------------- Written into output\image_00000000.ecc

DEMON
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Writing Nand
Done!
in 0:02 min:sec

Load Files Initiliazation Finished
14719
Started Creation of the 14719 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.04.515
---------------------------------------------------------------
building glitch image
---------------------------------------------------------------
C:\Users\Zach\Desktop\J-Runner v02 (278) Core Pack\001036403708\updflash.bin image built, info:
---------------------------------------------------------------
Console : Trinity
NAND size : 16MiB
Build : Glitch
Xell : power on console with console eject button
Serial : 001036403708
ConsoleId : 026789386425
MoboSerial: 9256528211030378
Mfg Date : 09/07/2020
CPU Key : 229265901E805F794ED839FBED913A85
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : 831B9700F0C289B350FC1684A76DED26
CF LDV : 3
KV type : type2 (hashed)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------

Saved to C:\Users\Zach\Desktop\J-Runner v02 (278) Core Pack\001036403708
Image is Ready
DEMON
Hardware : Demon Slim
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Writing Nand
Done!
in 0:25 min:sec

 

[Martin C]

Pic 4 - you've soldered SB to the wrong point.

 

[ScrubbaDubby]

well it was originally soldered correctly but i must have switched it when i resoldered. well i fixed it and soldered it back to the right one but still the same problems

 

[Martin C]

So have you done the necessary continuity checks?

 

[ScrubbaDubby]

yes. i have gone over all wires, re-soldered, double checked their position and consulted several people. so far no idea whats wrong. Just RDot and no LEDs on either demon or external usb.

ribbons are firmly in

 

[sick360mods]

Trim some of the exposed wire

Sent from my PC36100 using Tapatalk 2

 

[Martin C]

yes. i have gone over all wires, re-soldered, double checked their position and consulted several people. so far no idea whats wrong. Just RDot and no LEDs on either demon or external usb.

ribbons are firmly in

Are we talking about the same continuity checks?

So you've traced every QSB TP back to the console NAND and checked for shorts on adjacent QSB points?

 

[ScrubbaDubby]

i don't know what that is? that didnt make sense to me.

UPDATE!!! NO MORE RDOT BUTTTTT IT DOESN'T SWITCH NANDs! ITS ONLY BOOTING RGH NAND (DemoN NAND)

 

[Martin C]

i don't know what that is? that didnt make sense to me.

UPDATE!!! NO MORE RDOT BUTTTTT IT DOESN'T SWITCH NANDs! ITS ONLY BOOTING RGH NAND (DemoN NAND)

It makes sense to people who solder, which again is why this is for installation by someone experienced.

While you're at it, check that ribbon cable where it's plugged into the USB port as it looks too low. Hard to tell from here but you might have missed the port and gone under the connector.

 

[ScrubbaDubby]

@Martin C, you are truly my savior. Now that the RRoD is gone, the RGH is programmed successfully. It works 100%. learning experience i guess. Still don't know about that Red Dot. But, with some troubleshooting i installed a demon. Credit to everyone who helped! Mainly blak3y and martin c

 

[Martin C]

DemoN installs are the deep-end of learning this stuff. Glad you got there eventually.


Sent from my iPad using Tapatalk HD