FIXED demon xecuter & CR Rev c

Bravo1979

Full Member
Oct 25, 2012
28
0
Bethlehem
Hi everyone,
So, i have recently finished soldering a demon xecuter and CR Rev c to my xbox360 motherboard. I connected the demon xecuter to the CR Rev c with a ribbon cable. I launched J runner and did four nanddumps and they compared correctly. During the nand dump i had "Header is wrong" message. after the nand dump, I flashed the CR with the xsfv file but for reason the j runner said "sending xsfv file to demon" instead of CR. Anyway, after that, i clicked on create ecc and it said "Invalid image, failed to create ecc image.

Here is what happened during the J runner process...

Tuesday, January 08, 2013 4:02:28 PM

J-Runner v0.2 Beta (284) Started


All the best for 2013 - from Team JR!
Checking Files
Finished Checking Files
Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump1.bin
DEMON
Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Reading Nand
Done!
in 0:28 min:sec

Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Reading Nand
Header is wrong..
Done!
in 0:27 min:sec

Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump3.bin
Comparing...
Reading Nand
Nands are the same
Done!
in 0:27 min:sec

Comparing...
Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump4.bin
Reading Nand
Nands are the same
Done!
in 0:27 min:sec

Comparing...
Nands are the same
Programming Coolrunner
F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\common\xsvf\falcon_en.xsvf
sending xsvf to demon...
Done
Invalid Image
Failed to create ecc image
Invalid Image
Failed to create ecc image
Invalid Image
Failed to create ecc image
Invalid Image
Failed to create ecc image

I have attached a few detailed images of my soldering points.

I have read someone's post and he had sort of the same problem (his j runner gave the same messages) and he was told that he has soldering issues, so probably mine could be the same.

I kindly ask you to please take a look at my pictures and tell me where went wrong :)

if you need to see more pics, please let me know.

thanks in advance

View attachment 12931

View attachment 12932

View attachment 12933

View attachment 12934

View attachment 12935
 

BL4K3Y

VIP Member
Top Poster Of Month
Jul 7, 2010
13,223
118
At Home
You're reading the DemoN's NAND (which is blank when you receive the DemoN) when you should be reading the XBOX 360 NAND.

I suggest you read through the J-Runner PDF before doing anything else.
 
  • Like
Reactions: Bravo1979

firess

Full Member
Dec 10, 2011
46
0
Where ever the ARMY takes me.
If we could also get what dashboard that your on that would help too. But if you read the J-Runner PDF then all that is explained for you.

Also when you hook up the demon after you hooked up the power its always on the demon side so you would have to switch it over first then read the xbox 360 nand.
 
  • Like
Reactions: Bravo1979

Bravo1979

Full Member
Oct 25, 2012
28
0
Bethlehem
alright. i'll check that. thanks for the info BL4K4Y.

---------- Post added at 18:30 ---------- Previous post was at 18:28 ----------

the switch on the demon is switch to XB. I'm on dashboard 13599.
 

Bravo1979

Full Member
Oct 25, 2012
28
0
Bethlehem
do i have to toggle from demon to xbox before reading the NAND!? I just saw that option when i was going through the jrunner PDF!
 

Bravo1979

Full Member
Oct 25, 2012
28
0
Bethlehem
Cool. I'll give it a shot and I'll let you know what happens. Thanks indeed!

---------- Post added at 18:57 ---------- Previous post was at 18:51 ----------

I did a run and that's what i received.

uesday, January 08, 2013 6:53:25 PM

J-Runner v0.2 Beta (284) Started


All the best for 2013 - from Team JR!
Checking Files
Finished Checking Files
Current: XBOX
Switching to DemoN
Success
Current: DemoN
Switching to XBOX
Success
Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump1.bin
XBOX360
Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Reading Nand
Done!
in 0:27 min:sec

Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Reading Nand
Nand Initialization Finished
Done!
in 0:26 min:sec

Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump3.bin
Comparing...
Reading Nand
Nands are the same
Done!
in 0:26 min:sec

Comparing...
Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump4.bin
Reading Nand
Nands are the same
Done!
in 0:26 min:sec

Comparing...
Nands are the s

---------- Post added at 19:01 ---------- Previous post was at 18:57 ----------

should i flash the coolrunner now with this configuration?
 

Bravo1979

Full Member
Oct 25, 2012
28
0
Bethlehem
I have tested the demon before installation. I haven't done the boot test yet because according to the j runner PDF i should do it after flashing the CR. I used RGH ver1 because my dashboard is 13599 with CB 5771.
 

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
Also you are wired for RGH1, is this intentional as you will not be able to use XBL with that as the stock nand would need to be upgraded which would split the CB.
Which answers my question.

OP - DemoN installs are for people who know what they're doing, especially when it comes to the RGH process itself.

rather than see this turn into another 5-10 page help thread, stop and read everything before carrying on.
 

Bravo1979

Full Member
Oct 25, 2012
28
0
Bethlehem
Martin, thanks for the info. I've been for a while now. There is no other information other than what i found in your respected website and forum. when i did my first NAND dump, i had the toggle switched to demon which gave me header is wrong message and i found out that i needed it to be switched to xbox which i did and resulted in 4 perfect NAND dumps. now according to the j runner PDF , I should flash the cool runner and after that i should do a boot test. if all goes well, i should get a perfect boot. and after i should create an ecc image and so. I'm confident that i will be learning as i go through. according to the chart you made, RGH1 is the choice for my xbox, why, because my CB version is 5771 and my dashboard is 13599, if i needed to do an RGH2, i should be on 14xxx dashboard or so. what i don't know is when do i switch back and forth between the demon and the xbox. the j runner PDF doesn't say anything about that. and sorry for my lengthy message.
 

Bravo1979

Full Member
Oct 25, 2012
28
0
Bethlehem
Thanks guys for the info. As far as I read and according to Martin's chart, RGH2 is for a higher dashboard (14xxx) and mine is still on 13599. Anyway, at the beginning i had the EN spot on the cool runner soldered to the EN spot on the small piece that comes with the demon and attaches to the CR, soldered. and someone told me that i didn't need it and it's only used for RGH/fusion type so i removed it. few minutes ago, i was able to create ecc successfully and write ecc successfully, the current problem now is that i unable to boot the xbox, when i plug into power, it doesn't turn on. I'm not sure if it is something to do with wiring or i need to finish all steps before it is ready for loading. the reason i'm trying to turn it on is because i want to get the CPU key....any ideas!? thanks

---------- Post added at 21:22 ---------- Previous post was at 21:19 ----------

here is the info from j runner up until writing the ecc

Tuesday, January 08, 2013 6:53:25 PM

J-Runner v0.2 Beta (284) Started


All the best for 2013 - from Team JR!
Checking Files
Finished Checking Files
Current: XBOX
Switching to DemoN
Success
Current: DemoN
Switching to XBOX
Success
Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump1.bin
XBOX360
Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Reading Nand
Done!
in 0:27 min:sec

Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Reading Nand
Nand Initialization Finished
Done!
in 0:26 min:sec

Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump3.bin
Comparing...
Reading Nand
Nands are the same
Done!
in 0:26 min:sec

Comparing...
Reading Nand to F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump4.bin
Reading Nand
Nands are the same
Done!
in 0:26 min:sec

Comparing...
Nands are the same
Programming Coolrunner
F:\Xbox360\Reset Glitch Hack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\common\xsvf\falcon_en.xsvf
sending xsvf to demon...
Done
* unpacking flash image, ....
Spare Data found, will remove.
Removed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 1.6
CB_A: 5771
CB_B: missing
CD (image): 8453
CD (decrypted): 8453
* this image will be valid *only* for: falcon
* patching SMC...
Patching Falcon version 1.6 SMC at offset 0x12A3
* zero-pairing...
* constructing new image...
* encrypting CB...
* encrypting CD...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x1133F (0x9340 bytes) CB_A 5771
0x11340..0x1733F (0x6000 bytes) CD 8453
0x17340..0xBFFFF (0xA8CC0 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...Done!
------------- Written into output\image_00000000.ecc

XBOX360
Hardware : Demon Phat
Firmware : 1.0
Flash ID : 0x73AD Hynix (16MiB - Small block)
Flash Size : 0x400 blocks of 0x4200 bytes
Writing Nand
Done!
 

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
Can you stop posting for an hour or two and have a good read over everything on this site.

you need a much better understanding of the process, which can only be attained by reading.