GENERAL demond remove

[skater411]

what im trying to do is just remove the demon an start back over desoldering does not work at all so i try desodlering pump alittle better not much

 

[Antalpromille]

what im trying to do is just remove the demon an start back over desoldering does not work at all so i try desodlering pump alittle better not much

Hot air is the answer, in a controlled form so you wont burn your demon.

 

[skater411]

i figure out my error now my rgh boot up but my demon stock nand does not boot up im very new to the demon install i did one other and i tore pad off bc i was using micro port on back after it was install my bad anyway . i wonder what my issue is now any help would be highly appericated thanks

 

[socalbill]

no pics, no help..and use a little Chip Quik to desolder the demon

 

[skater411]

ok ill load pic i dnt need to desolder it anymore i just need to get demon booting when i try to power it on it dose nothign xbox does not come on works fine on the rgh side ithink i got some programming issue

 

[skater411]

so u need pic of my install your saying



http://i47.tinypic.com/eh0up2.jpg


ttp://i47.tinypic.com/np5mko.jpg
http://i50.tinypic.com/2dmh2j6.jpg

http://i49.tinypic.com/2qsyvf6.jpg

 

[Duhasst0]

Yes post some pics let us see whats up.

 

[skater411]

dude like it does now allow me write to xbox 360 but on demon it does i can write the hacked image to demon but when i try write stock to 360 it give me error code manufacturer for code FF not found

i had this error code once day i fixed it i think i may have some more bridge damn they was not lie this thign not that easy to install it has cost me my vip today thanks martin bc i hijack a post really great wonderful fml

---------- Post added at 14:52 ---------- Previous post was at 14:50 ----------

man can u get on aim

 

[skater411]

so it not allowing me pretty much to write to xbox but it will write to the demon . i wonder what going on

---------- Post added at 15:15 ---------- Previous post was at 15:08 ----------

http://imageshack.us/g/11/img1166l.jpg/

---------- Post added at 15:17 ---------- Previous post was at 15:15 ----------

ok there all my pic

 

[jsinger47]

Your soldering is very poor. too much exposed wire. Lack of or bad fluxing of demon points. Shouldn't this be obvious?

In the case of a spelling error, I blame Tapatalk.

 

[Martin C]

Why haven't you posted in the 'request a service or item' section yet?

This is obviously beyond your ability.

 

[skater411]

ok well i can read from demon an write to it cant write to xbox side ?

 

[Martin C]

Which tells you........?

 

[skater411]

im not really sure that why i was asking u i was thinking mabey it could be bridge point the rgh side works prefect i have rgh many xbox this like first demon install i done that was full

 

[Duhasst0]

Lets see some pics or you can send it off to me or someone else here on the forum dude. Looks to be the only way to figure out what is really going on.

 

[Martin C]

It tells you that your soldering (as suspected) is at fault.

 

[skater411]

ok thanks ill check it out re do some stuff

 

[Martin C]

You've not even stated what error message you get - I wish you would stop wasting other people's time.

 

[skater411]

i did before i guess u did not get it

---------- Post added at 01:06 ---------- Previous post was at 01:04 ----------

manufacturer for code FF not found

 

[Martin C]

So that's soldering - all day, every day.