Hello, I have a V2 mobo 4GB CORONA post fix ok, I r / w nand qsb CORONA DGX 1.0s, kindly wanted to know once wrote DGX and unplugged the usb nand reader, how can I see the information WITH J-RUNNER IN MONITOR COM? HOW TO COMMUNICATE? And which COM port?DGX HOW TO MONITOR COM J-RUNNER????
- Thread starter TENCULO
- Start date
Hello, I have a V2 mobo 4GB CORONA post fix ok, I r / w nand qsb CORONA DGX 1.0s, kindly wanted to know once wrote DGX and unplugged the usb nand reader, how can I see the information WITH J-RUNNER IN MONITOR COM? HOW TO COMMUNICATE? And which COM port?
i got that far with my DGX and got my port open
but so far all i have is a blinking green light
and com thats says
"Port opened at 2/5/2013 11:11:41 PM"
OP <<< --- INSTALL THE DRIVERS
but so far all i have is a blinking green light
and com thats says
"Port opened at 2/5/2013 11:11:41 PM"
OP <<< --- INSTALL THE DRIVERS
But what are you using to monitor comms? I use a ck3i with modified dvd power plug, there's a pic in jrunner.
Last edited:
I'm at the same point, wrote dgx ecc to nand and have dgx with blinking green light. I have nand x usb update cable, I seen illustrations in jrunner image but I think I'm over complicating it, do I need ck3i? I'm working on a trinity. Please help!
Last edited:
I am at the same point, scratching my head...
I have Slim Trinity with 15574.
'DGX v1.0S' installed to 'Trinity QSB v3'
Installed 'Slim Post QSB' on the back.
Trying different wire lengths...
What i am not sure is the cable for 'Monitor COM'...
I am using J-Runner v0.2 Beta (287)
Also i have the Demon installed but not using it since i couldn't get my keys yet. (Although tested and confirmed that it's operational)
My settings are:
Demon is on XB and switched to XBOX Nand.
DGX all switches are on the side; closer to the big chip.
'Nand-X USB Update Cable' appears as COM3 and selected as same on the monitor.
Demon, J-Runner and cable software/firmware/drivers are latest.
I am hoping that the 'Nand-X USB Update Cable' mentioned on the J-Runner pdf manual is the same thing as the 'J-RUNNER USB COMMS CABLE' since i have this cable that came with my 'Nand-X RGH Edition' and it is connected to the port on the 'Trinity QSB v3'.
I have written ECC for DGX after dumps.
I even compared my dumps from demon with Nand-X and all are OK. (Nand-X, Trinity QSB v3 and DGX worked connected alltogether)
On DGX, red light on, green blinks once in a while.
Xbox green light blinks until forever.
I hope i don't have to uninstall demon from the back...
I would very much appreciate if someone could confirm i'm on the right track.
Thanks in advance.
Here are my photos:
I have Slim Trinity with 15574.
'DGX v1.0S' installed to 'Trinity QSB v3'
Installed 'Slim Post QSB' on the back.
Trying different wire lengths...
What i am not sure is the cable for 'Monitor COM'...
I am using J-Runner v0.2 Beta (287)
Also i have the Demon installed but not using it since i couldn't get my keys yet. (Although tested and confirmed that it's operational)
My settings are:
Demon is on XB and switched to XBOX Nand.
DGX all switches are on the side; closer to the big chip.
'Nand-X USB Update Cable' appears as COM3 and selected as same on the monitor.
Demon, J-Runner and cable software/firmware/drivers are latest.
I am hoping that the 'Nand-X USB Update Cable' mentioned on the J-Runner pdf manual is the same thing as the 'J-RUNNER USB COMMS CABLE' since i have this cable that came with my 'Nand-X RGH Edition' and it is connected to the port on the 'Trinity QSB v3'.
I have written ECC for DGX after dumps.
I even compared my dumps from demon with Nand-X and all are OK. (Nand-X, Trinity QSB v3 and DGX worked connected alltogether)
On DGX, red light on, green blinks once in a while.
Xbox green light blinks until forever.
I hope i don't have to uninstall demon from the back...
I would very much appreciate if someone could confirm i'm on the right track.
Thanks in advance.
Here are my photos:
Martin C
VIP Member