DGX dgx v1.1s

[mrsax307]

any one have a sledge hammer i can borrow this dam dgx been blinking away at me for hours i even got the new dgx 1.1s still no luck i have tried everything this trinity just dont wanna glitch i have done many jtag rgh and demon installs trid atl points add the cap tried the red dot method and this dgx green light just blinking away at me haunting me in my sleep hammer any one

 

[-DoC-]

How about pics?

Its not the DGXs fault. I've done a few Trinity's. Glitch within 3 mins. Its all about wire length and positioning.

Sent from my DROID RAZR using Tapatalk 2

 

[BL4K3Y]

Trinity installs have already been proven to be less reliable than Corona.

Why don't you start by posting some images and a J-Runner log?

 

[mrsax307]

i have bad blocks Bad Block ID @ 0x0044 [Offset: 0x118800]
Bad Block ID @ 0x0045 [Offset: 0x11CA00]

---------- Post added at 16:04 ---------- Previous post was at 15:58 ----------

http://s1357.beta.photobucket.com/user/mrsax307/library/xbox

 

[BL4K3Y]

Why have you soldered E & F directly to the points on the motherboard?

The QSB has solder pads on with a trace run to the correct pads.

 

[mrsax307]

by the way the yellow wire is alt point for cpu post out cuz of so much soldering to the other pad dont trust it and i have tried many diff cpu reset configurations

---------- Post added at 16:09 ---------- Previous post was at 16:09 ----------

b/c i didnt think they were working but as it turns out they were fine

 

[Steel City Mods]

If youve had to solder so many times to a single pad that you cant trust the weld, time to give up.. The qsb pads dont ever fail either, unless you lift them, theyre great products. Why doubt a great product before questioning your own ability?

 

[mrsax307]

its not the quick solder pads i was taling about its the cpu post point

---------- Post added at 16:16 ---------- Previous post was at 16:14 ----------

you got to remember i owned 3 dgxs v1.0 v1.0s and now v1.1s thats alot of messing around with the pads on the mobo

 

[Steel City Mods]

I know what you were talking about.. I was covering both aspects at once.. BL4K3Y asked why you soldered to nand points directly instead of qsb points, you said you felt they werent working.. And you said you went to alt point cause you felt the normal point was soldered too many times to trust, why solder so many times? This isnt very hard by any means, just requires a little skill and patience.

 

[BL4K3Y]

You still haven't done what I asked.

We need ALL of your installation images and a FULL J-Runner log.

 

[mrsax307]

http://team-xecuter.com/forums/showthread.php?t=76145 thats the cpu post out im using

---------- Post added at 16:22 ---------- Previous post was at 16:21 ----------

ok give me a few seconds i was still trying to glitch it

 

[Steel City Mods]

http://team-xecuter.com/forums/showthread.php?t=76145 thats the cpu post out im using

---------- Post added at 16:22 ---------- Previous post was at 16:21 ----------

ok give me a few seconds i was still trying to glitch it

No, that what somebody else is using lol.. Pics of somebody elses work doesnt reflect your problem whatsoever.

 

[mrsax307]

http://s1357.beta.photobucket.com/user/mrsax307/library/xbox i dont have a log

---------- Post added at 16:40 ---------- Previous post was at 16:39 ----------

No, that what somebody else is using lol.. Pics of somebody elses work doesnt reflect your problem whatsoever.

i was showing you where my yellow wire was ran to

---------- Post added at 16:44 ---------- Previous post was at 16:40 ----------

my log dont say much Wednesday, February 13, 2013 6:43:04 PM

J-Runner v0.2 Beta (287) Started


WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button


Checking Files
Finished Checking Files
Downloaded *xeBuild/15574/bin/patches_falcon.bin
Downloaded *xeBuild/15574/bin/patches_fat.bin
Downloaded *xeBuild/15574/bin/patches_g2falcon.bin
Downloaded *xeBuild/15574/bin/patches_g2jasper.bin
Downloaded *xeBuild/15574/bin/patches_g2trinity.bin
Downloaded *xeBuild/15574/bin/patches_g2zephyr.bin
Downloaded *xeBuild/15574/bin/patches_jasper.bin
Downloaded *xeBuild/15574/bin/patches_trinity.bin
Downloaded *xeBuild/15574/bin/patches_xenon.bin
Downloaded *xeBuild/15574/bin/patches_zephyr.bin
Downloaded *xeBuild/15574/_glitch.ini
Downloaded *xeBuild/15574/_glitch2.ini
Downloaded *xeBuild/15574/_jtag.ini
Downloaded *xeBuild/15574/_retail.ini
Finished Checking Files
Initializing KEVINSLIM.bin..
Nand Initialization Finished
Tip: Load the nand on source to have quicker results.
Scanning....
No Xbox Detected
Finished

 

[mrsax307]

if the dgx led is bright red and the green one is flashing all my points are connected i would think being that i have been trying to glitch the xbox for a wile went threw all three revisions as they came out tried every install guide i could find one by one trying every install method every fix every wire length every size wire found in every guide posted on this forum and now on to the newest dgx 1.1s that im sure most of you have not even tried yet cuz its so new i figured i would ask for help not ask for someone to bust my balls if their is any one who can really help i would appreciate it thanks

p.s i did everything by the book i installed nand x got my back ups compared them in hex and in j runner then flashed dgx to my nand for my mother board then installed dgx now trying to glitch it out and get my cpu key never in all my jtag rgh demon led rapid fire or any other chip i have installed in all my systems gamecube ps1 ps2 xbox xbox 360 or my ps3 have i ever had problem that i just couldnt figure out my self this is a first for me

 

[Steel City Mods]

Nobodys busting your balls. You just finally posted pics, so now youll receive help.. I use thicker wire on the cpu rst, usually a ground from a coolrunner kit, and generally like 55 cm for the post out works for me.

 

[mrsax307]

i tried that already with no luck this is the new dgx wire im using and the cpu post wire is deff alot thicker then the previous versions and its 70 cm i guess i can cut it thanks

---------- Post added at 17:17 ---------- Previous post was at 17:09 ----------

maybe i should go back to the r4d4 point for my cpu reset like team xecuter said in the preview for the dgx 1.1s before i say 55cm didnt work for me

 

[Steel City Mods]

R4d4 works very well.. and cutting the wire down is ok, but id also just try uncoiling it from the fan first, i leave my 55cm wire loose hanging off the board

 

[mrsax307]

ok will try it right now thanks

---------- Post added at 17:29 ---------- Previous post was at 17:21 ----------

same the green light is just flashing away lol

 

[Steel City Mods]

Have you tried powering on with the hdmi plugged in?

 

[Martin C]

why did you solder E&F to the QSB points instead of the pads? Do you not own a multi-meter?