im wondering if it matters which nand you write the gliched image to when useing the dgx 1.1s ....etheir the demon nand or the xbox nand? and what if you accidently uninstalled the demon usb driver and cant get them installed anymore because the demon is all ready soldered in the motherboard and your not suppose to put it in bootloader mode and YES i have already tryed to reinstall the usb drivers without it in bootloader mode and it does NOT work?
does it matter which nand you write to
- Thread starter jw159163
- Start date
i had the cr3 pro and J-R programmer and was going to use the rater feature and i install the usb driver for the j-r programmer and the demon said unrecognized usb device ever since
what if i hold the demon button down while i plug in my xbox and hold it down while i plug the cable into my laptop and instal demon tools which installs the drivers...do you think that will work?
TheGlow
VIP Member
I dont know about other people but my Demon does this to me a lot, unrecognized device. I usually need to unplug the power to the 360 for 10-15 seconds, then power it back up and my PC will detect it.
Sadly though when doing a dump or write in jrunner, it may error out, and then same thing. I wont be able to toggle with the adapter button, and if I disconnect/reconnect the USB, unrecognized device.
What seems to work for me is plug power into the 360, then plug in USB.
Then do a nand dump in the demon application, not jrunner. If it doesnt error, then it looks like a "good" connection. Then I open Jrunner and do what needs doing.
It seems to die more frequently if I go right into using Jrunner.
I plan to remove this weekend and put in a different system, hopefully the behavior will change.
Sadly though when doing a dump or write in jrunner, it may error out, and then same thing. I wont be able to toggle with the adapter button, and if I disconnect/reconnect the USB, unrecognized device.
What seems to work for me is plug power into the 360, then plug in USB.
Then do a nand dump in the demon application, not jrunner. If it doesnt error, then it looks like a "good" connection. Then I open Jrunner and do what needs doing.
It seems to die more frequently if I go right into using Jrunner.
I plan to remove this weekend and put in a different system, hopefully the behavior will change.
does anyone know how to get the usb drivers for the demon without useing the demon toolbox so i can install them my self and should it work even if the demon is not in bootloader mode
just curious how can you unsolder those tiny points that hold the demon down. im curious because i want to take mine off as well?
TheGlow
VIP Member
well Demon Toolbox install instructions say theres a checkbox for the drivers.
I havent done it in over a year so I don't recall.
Try uninstalling the toolbox, then reinstall. theres a good chance the demon drivers would be in the toolbox directory as most apps leave the driver behind for reinstallation purposes.
I havent done it in over a year so I don't recall.
Try uninstalling the toolbox, then reinstall. theres a good chance the demon drivers would be in the toolbox directory as most apps leave the driver behind for reinstallation purposes.
i wish it was that easy but ive tryed that many times i really need a way to unsolder the demon completely so i can flip the switch to pc and reinstall drivers and probally firmware as well but i dont want to f up my demon while unsoldering those tiny ass points..any advice?
JRP drivers will not uninstall anything. I've seen this issue before. It's either the ribbon cable not installed properly (which is easy to mess up) or an install problem with the Demon itself. I think you should post images of your install. Your most likely chasing the wrong problem.
And besides, the Demon does not have to be hooked up to install the drivers. That's the way USB devices work with an auto installer such as ToolKit. ;p
Tapatalk misspelled it. Knot me.
And besides, the Demon does not have to be hooked up to install the drivers. That's the way USB devices work with an auto installer such as ToolKit. ;p
Tapatalk misspelled it. Knot me.
Last edited:
so the fcc cable that is covered in metal tape or whatever has a metal pin on each end that is folded back is that mean that it is come apart or was it made like that?
TheGlow
VIP Member
Also you shouldn't need to desolder the whole demon to test.
As long as the power cord is not connected to the 360 at all, you should still be able to connect a micro usb in and set it to pc.
you cant do switch on PC AND have the power plugged in.
As long as the power cord is not connected to the 360 at all, you should still be able to connect a micro usb in and set it to pc.
you cant do switch on PC AND have the power plugged in.
blakhawk
Full Member
Just do what @TheGlow said, I have done this many times without any issues. Just remember to switch back..
well i didnt do all that but i did unsolder the demon and put it on pc and it still say unrecognized device so what does that mean that it doesnt work anymore?