can I wire up my rjtag console without using the phat qsbkit v3. I can read the nand its just the other wires where they go on the board.
doing rjtag with out phat qsb kit v3
- Thread starter rick48235
- Start date
trippy86
VIP Member
Re: donng rjtag with out phat qsb kit v3
yes you can, for D, E & F its the same as the rgh 2.0 wiring. K im not 100% sure which point it is.
and obviously you want to use the 5v point, not the 3v3
yes you can, for D, E & F its the same as the rgh 2.0 wiring. K im not 100% sure which point it is.
and obviously you want to use the 5v point, not the 3v3
Last edited:
Re: donng rjtag with out phat qsb kit v3
how about the b point on rgh2 where does it go on rjtag. iam thinking it might be where k goes???
how about the b point on rgh2 where does it go on rjtag. iam thinking it might be where k goes???
Last edited:
trippy86
VIP Member
Re: donng rjtag with out phat qsb kit v3
this video tells you exactly what points to solder to
http://www.youtube.com/watch?v=x1DzLRoZ7Ik
this video tells you exactly what points to solder to
http://www.youtube.com/watch?v=x1DzLRoZ7Ik
trippy86
VIP Member
Re: donng rjtag with out phat qsb kit v3
have you read the instructions for r-jtag?????? I would if i were you, unless you want a broken console
you dont use point B
have you read the instructions for r-jtag?????? I would if i were you, unless you want a broken console
you dont use point B
Re: donng rjtag with out phat qsb kit v3
no I read everything I was just wondering where point b is used. the video says k is orange and in rgh2 orange is point b he wires it up with qsb in video. looks like the qsb is solder to point b on rjtag. r4b24 look. its being used
no I read everything I was just wondering where point b is used. the video says k is orange and in rgh2 orange is point b he wires it up with qsb in video. looks like the qsb is solder to point b on rjtag. r4b24 look. its being used
Last edited:
Utmad
VIP Member
trippy86
VIP Member
Re: donng rjtag with out phat qsb kit v3
doesent the qsb use it on rjtag. it ties into the circuit.
Last edited:
Re: donng rjtag with out phat qsb kit v3
looking at it more b might go with b on the rjtag board
looking at it more b might go with b on the rjtag board
Martin C
VIP Member
Re: donng rjtag with out phat qsb kit v3
Get the QSBs. They are perfect for people such as yourself.
trippy86
VIP Member
Re: donng rjtag with out phat qsb kit v3
you have been told more than once by numerous people. B is not used!!!!
you have been told more than once by numerous people. B is not used!!!!
rdubbs007
VIP Member
trippy86
VIP Member
Re: donng rjtag with out phat qsb kit v3
i knew what it was, just couldnt remember which specific point it was
i knew what it was, just couldnt remember which specific point it was
Re: donng rjtag with out phat qsb kit v3
i do appreciate his efforts in trying to help others though.
The wiring in that video is a mess - im surprised he got it booting at all :/
i do appreciate his efforts in trying to help others though.
nofeloniesyet
VIP Member
Re: donng rjtag with out phat qsb kit v3
same point demon uses for kiosk (orange wire)
cynder9792
Full Member
I have also been watching that video referenced above but it is not specific enough when it comes to the points for the post out qsb and the jtag qsb (although the pic for the jtag qsb is easier to see). The small points along the top of the qsb are hard to see as if it is all points or some. I am still searching for the correct answer as I am at the point where I install the bottom qsb's and do not want to take the chance of soldering/not soldering the correct points on such a small area.
