LITEON DG-16D4S - SLIM Drive doesn't Eject

[Rapitharian]

I have a Liteon DG-16D4S drive.
It had a board with the Winbond chipset which I removed and replaced with the team xecuter unlocked PCB. I had the Board installed and working with LT+V2.0.
Last night I went to upgrade the drive to LT+V3.0.
I reverted to stock and then found the Drive will not eject.

What could I be doing wrong?

Thanks for the Help,
-Rap

 

[BL4K3Y]

Can you post your JungleFlasher log from when you reverted to stock firmware please.

 

[Rapitharian]

Log below.
Thanks again.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.92 Beta (304)
Session Started Thu Feb 15 19:23:17 2012

This is a Wow 64 process running on 2 x 64 bit CPUs
X360USB PRO detected, Version 0.18

Found 1 I/O Ports.
Found 4 windows drives A: C: D: E:
Found 2 CD/DVD drives D: E:

Sending Vendor Intro to port 0x0000
Status 0x51
Re-sending Vendor Intro:
........................................................
Serial flash found with Status 0x72

Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xEF
Device ID: 0x11
Flash Name: Winbond/NEX(W25P20/NX25P20)
Flash Size: 262144 bytes

Sending Spi UnLock request to Port 0x0000
.
Spi Status: 0x00
Loading firmware file C:\JungleFlasher\Firmware Backup\0225-1.bin
MD5 hash: 1393d6dd71363bc971dd6ddeba6a7494
Inquiry string found
Identify string found
Drive key @ 0xA030 XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Firmware Osig: [PLDS DG-16D4S 0225]
Firmware is: SlimKey Extract
Loading firmware file C:\JungleFlasher\Firmware Backup\0225-1.bin
MD5 hash: 1393d6dd71363bc971dd6ddeba6a7494
Inquiry string found
Identify string found
Parse Failed !

Loading firmware file C:\JungleFlasher\firmware\Orig-0225u.bin
MD5 hash: 450a16f4672662eb47b540323bc778a7
Drive key @ n/a FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Firmware Osig: [PLDS DG-16D4S 0225]
Firmware is: Stock
Spoofing Target
DVD Key copied to target
Key Sector copied from Source to Target
Target is LT - ID strings not copied to Target


Getting Status from port 0x0000
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x0000
Erasing:
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................

Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !


Sending Spi Lock request to Port 0x0000
Spi Status: 0x8C
Sending Vendor Outro to port 0x0000
Sending Vendor Outro to port 0x0000
Drive is Slim Lite-On..

Key found in KeyDB at record (1 - firmware)
Key is: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Key has been tested and verified, thanks C4eva !
Sending Vendor Outro to port 0x0000
Drive is Slim Lite-On..

Key found in KeyDB at record (1 - firmware)
Key is: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Key has been tested and verified, thanks C4eva !

 

[Rapitharian]

I found the issue.!!!
After looking at the drive and playing in JF, I realized the PCB was taking the flash, it was as if the drive was not getting power to the motors, tray doesn't open and the laser doesn't light.

This made me think, is there an issue with the wires?

To be sure, I removed the no solder block and the connector wire. I soldered the main wires from the drive directly to the PCB.

Once done I tested the drive and VIOLA, it worked!

Thanks for giving me a place to noodle this through.

I hope this post helps others.

Seems to me, that no solder block is a pain in the 4SS and a likely source of issues.

-Rap

 

[Sundance]

i have same issue, no drive spining and drive wont eject
Near the open tray motor is there 3 cables (White, Yellow and Green) Yellow and Green are in short circuit (i mean, there is continuity between them) I thinks this is a switch, isnt?

When i sold all the cables directly to PCB unlocked i get continuity in all cables... what i have to see?

Thanks in advance

 

[BL4K3Y]

i have same issue, no drive spining and drive wont eject
Near the open tray motor is there 3 cables (White, Yellow and Green) Yellow and Green are in short circuit (i mean, there is continuity between them) I thinks this is a switch, isnt?

When i sold all the cables directly to PCB unlocked i get continuity in all cables... what i have to see?

Thanks in advance

Please start your own thread, don't hi-jack others.

This is clearly stated in the rules you were prompted to read when you joined the forum .