Dumped as Corona V3 but was V4 and now..

[Sundance]

I had used corona v3 method to dump nand with JRunner
But was a Corona V4.
I was tired last night and start this machine, i used a USB Reader to dump Nand, using V3 method (normal way) i start JRunner and then "Read", program ask about what version and i select "Corona", the start reading, twice, all ok 16mb extraction nand compare and all same. Then i wrote Ecc DGX and then install DGX properly.
DGX start glitching about 5 times then red light central.
Check all connections and all are ok.
Thought i never wrote Ecc DGX so start JRunner load nand and it says "Wrong header"
In that instant of light i saw the memory in the middle of the board, and yes, its was a Corona V4 and not a V3...
I had Removed all connections (Reader USB and DGX)
and then i had installed SD card reader (from Maximus), start JRunner, then read, select Corona 4GB, select reader and then 48MB extraction start
Nand are the same, all ok.

Do you think i need to flash first dump with same method? Would anyone happen this?

Thanks in advance

 

[frostbyt]

You haven't posted any pics and I assume you have the post fix adapter.

 

[Sundance]

You haven't posted any pics and I assume you have the post fix adapter.

You assume correctly, i use XECUTER POST_OUT_FIX adapter, and its the first thing that i do with coronas V3 V4

I have not mentioned it, because my problem is what to do with first dump that i did, also did the Ecc DGX into it

1st ill try to get CPU KEY and then ill comment my results.

 

[nishat]

Iis your console boot with stock nand if it is booting properly then place nand dump 1 in the source and write DGX and u need a lan cable or nand x update cable to grab your cpu key because every corona dont give a video.

 

[Sundance]

Iis your console boot with stock nand if it is booting properly then place nand dump 1 in the source and write DGX and u need a lan cable or nand x update cable to grab your cpu key because every corona dont give a video.

I think you dont understand my problem.


I installed DGX, it glitch some times and stop, this is telling me is into xell, i used so many times, but now never gets IP address, when i turn off console central Green led is ON

Please someone confirm that if i can write the file that ive dumped first time, the file that is dumped using trinity or v1 v3 method to get nand that i used by mistake (i wrote ecc dgx on it)

I know V4 has 4GB nand memory, and i success to get 48MB dump, but this was later, first i make mistake dumping as V3, what are those 16MB that ive read? there are 2 nands?

I think that my mistake makes this about cant get ip address from console = cant get cpu_key

Thanks

EDIT; SOLVED.
1st dump 16MB was totally blank, i edited with HEX editor and nothig inside, i take all DGX connections restore original from 48mb and xbox starts fine.
The other problem, about DGX not load, was that when boot xells crash, i try diferent files until i use com monitor and when xbox load xell all work like a charm, i finally get cpu key.

 

[Martin C]

In other words you didn't do a sanity check when you originally dumped.

If the dump was empty, it would say the dumps match, however you would have received the message 'header is wrong'.

 

[Sundance]

In other words you didn't do a sanity check when you originally dumped.

If the dump was empty, it would say the dumps match, however you would have received the message 'header is wrong'.

Yesterday when trying to read again using method V3 to check what its into it i get the messagge "Warning: header bla bla..." but first time i not see that message

I had this problem because i was trying to work quickly and i forget to identify the nand controller chip, assuming was a Corona V3

Thanks for all replys, you can close this thread