Error: 258, 218, 8251, 8201 for NAND.

[ponuod]

(doing of my mate, need help)
Falcon:

1. installed rgh
2. run the XELL, saved all valued data
3. builded glitch image and wrote via usb flash

after that on booting by "POWER" button, Xell is loading, not a dash

4. tried to write *.ecc file again and got bunch of errors.

Now console does not powering on, and nand-x can't read/write nand.

C:\nandpro3>nandpro usb: -r16 nanddump.bin
NandPro v3.0a by Tiros

Looking for usb interface device
Flash Config: 0x01198010
Block Size: 16KB Block Limits: 0x000000..0x0003FF
File: nanddump.bin
Reading
Error: 258 reading block 0
Error: 218 reading block 1
Error:8251 reading block 2
Error:8201 reading block 3
Error:8201 reading block 4
Error:8201 reading block 5
Error:8201 reading block 6
Error:8201 reading block 7
Error:8201 reading block 8
Error:8201 reading block 9
Error:8201 reading block A
Error:8201 reading block B
Error:8201 reading block C
Error:8201 reading block D
Error:8201 reading block E
...

Thanks.

 

[jtag360.nl]

To write your ecc file again to the nand you must use this command.

nandpro usb: +w16 image_00000000.ecc

In your example you are reading the nand.

 

[axelll]

Why don't you try J-Runner, it'll take care of bad blocks automatically...

 

[axelll]

Also, check NAND-X soldering

 

[ponuod]

Same errors on read and write,
and this does not looks like bad block, since problem with reading EVERY block.
nand-x is working good on other consoles [tested].

---------- Post added at 00:19 ---------- Previous post was at 00:14 ----------

Also, check NAND-X soldering

Mate says that soldering is fine since on other console soldering in the same way is working fine.

 

[axelll]

Could be a bad NAND, maybe smth happened when you wrote the ecc and the NAND is corrupt. If you are sure that the NAND copies you downloaded are OK, shorting out pins 44 and 47(search for the thread on this forum) will kick the nand in recovery mode. Then you'll be able to access the NAND. Also, make sure that there aren;t some cold joints on your soldering.

 

[tonyjandc]

for what i gather your getting this error from the offset . this is a bad image do as axell states short out pins 44-47 reset nand and reflash orginal resolder nandx cables and start again. fresh read and fresh install. looks like you corrupted the dash flash . I knocked my nandx once when installing freeboot and got bad errors. if unsure how to reset nand

 

[Martin C]

Pics of soldering. Also, make sure you reset the NAND-x and console between tries.

So unplug both, then connect console and then connect NAND-x to USB.

 

[ponuod]

Pics of soldering. Also, make sure you reset the NAND-x and console between tries.

So unplug both, then connect console and then connect NAND-x to USB.

To reset nand-x i should:

1. connect only by usb to pc
2. press black button for how long ?
3. and wait how long to reset

v3 code will be lost on nand-x ?

 

[Martin C]

I don't believe I mentioned the black button.

To reset the NAND-x, you unplug it from the USB, give it a couple of seconds and plug it in again.

 

[ponuod]

I don't believe I mentioned the black button.

To reset the NAND-x, you unplug it from the USB, give it a couple of seconds and plug it in again.

Ok,
what the button for then ?

 

[ponuod]

nandpro usb: -e16

solved the problem.