RGH failed rgh

[jhaymes2006]

i flashed my nand with rgh i had coolrunner installed would flash green stayed solid red but xbox power button just flashed green. anyway i want to flash the nand back to stock i have original nand dump, and i also have dvd key from flashing, am i going to be able to do it with just these two things. i wont be able to get my cpu from xell ive already taken everything out, except nand writing wires from nand x. so please tell me how to get it back working stock.

 

[Justice1231]

This may sound like a silly question but when you say the xbox button just flashed, did you have the dvd drive connected?

 

[jhaymes2006]

Yes

---------- Post added at 00:35 ---------- Previous post was at 00:34 ----------

Was that a bad thing

 

[neophyte5001]

i flashed my nand with rgh i had coolrunner installed would flash green stayed solid red but xbox power button just flashed green. anyway i want to flash the nand back to stock i have original nand dump, and i also have dvd key from flashing, am i going to be able to do it with just these two things. i wont be able to get my cpu from xell ive already taken everything out, except nand writing wires from nand x. so please tell me how to get it back working stock.

Giving up? Okay, to each his own.

To rewrite nand (original nand) I will assume a few things. If you have a big block nand the only thing that matters is the first 64 but I have a jasper 512 so if I wanted to rewrite my nand I would use this:

nandpro usb: -w512 nanddump.bin

see the - before the w? make sure you use that, and power cycle (unplug your box for about 1 min) after flashing has completed.

There is great support here. If you change your mind and decide to give it another go...

 

[Justice1231]

Ok, no probs you what board do you have?

---------- Post added at 17:09 ---------- Previous post was at 17:07 ----------

Yes

---------- Post added at 00:35 ---------- Previous post was at 00:34 ----------

Was that a bad thing

No not at all. when i think of a flashing centre button i think of the dvd drive not connected or F/W fault.

 

[jhaymes2006]

If I should have had the DVD drive unplugged and the was all it was I'm going to redo it because I had checked my pll bypass and was not bridged. It was just midnight and I was frustrated.

---------- Post added at 00:40 ---------- Previous post was at 00:39 ----------

Jasper 256 I ran it all as big block NAND and programmed coolrunner with NAND x v. 3 and jasper files.

 

[Justice1231]

If I should have had the DVD drive unplugged and the was all it was I'm going to redo it because I had checked my pll bypass and was not bridged. It was just midnight and I was frustrated.

---------- Post added at 00:40 ---------- Previous post was at 00:39 ----------

Jasper 256 I ran it all as big block NAND and programmed coolrunner with NAND x v. 3 and jasper files.

Im not saying that is the problem, just trying to rule out all possiblilites, hang fire till one of the pros has a look and maybe they will be able to shed some light on it.
It took my three attempts to get it right. the first attempt i lifted a resistor, second attempt all seemed well but just got a black screen when trying to load the hacked dash. and third attemp everthing went well. my second error i beleive was my incorrect image as i suffered from monkey see monkey do syndrome, i followed a tut on here and instead of selecting my MOBO i selected the one on the tut, hence to say i was a bit embarresed lol.

 

[jhaymes2006]

I see what your saying, I was just hoping that was all that it was. Thanks for the help

 

[neophyte5001]

If I should have had the DVD drive unplugged and the was all it was I'm going to redo it because I had checked my pll bypass and was not bridged. It was just midnight and I was frustrated.

---------- Post added at 00:40 ---------- Previous post was at 00:39 ----------

Jasper 256 I ran it all as big block NAND and programmed coolrunner with NAND x v. 3 and jasper files.

So... you pulled out all the wires, but now you want to redo it? If so, that's fine but when you have a snag this time help yourself and

Stop

Breathe

Post your prob on this forum

Wait

Someone will help you out! I understand how frustrating it can be when things don't work like they should but TX products are second to none and support is top notch. Between the products and the support, the only thing stopping you from getting to your goal will only be you!

From what you posted, it could've been a bad flash, you gotta take this step by step and be patient man.

Take care re-soldering those wires, get the HW side back up and come back and let us know where you are at that point.

 

[jhaymes2006]

Thanks for all of the help already.

 

[GSIBOY]

Let us know if you're good to go

 

[MODCUS]

Okay re solder the wires, but this time with your orange wire, replace it with another wire a little longer and use the alternative point under the board, make sure your .ECC file was made either with 360 Multibuilder or python directly, then follow the tutorial ur using like normal, if you need to know the alternative point, look on the sticky uber made. I have done 3 consoles, a falcon, worked fine, a 512 Jasper (used alternative point and it was working fine), and just yesterday a slim and i also had to use alternative point, its just easier to solder to and also you can see easily if its connected well, the point by the HANA is very small and hard to see if the wire might be touching something else or what ever.