RGH Falcon 0022

[mm53668]

Ok received a console today that someone botched an RGH. It wouldn't glitch. The stby_clk resistor was completly removed. So I stole a resistor off an old zephyr installed and the readings check out at right around 33-34 OHMs. So I scratched the trace further down away from the hana and still same readings there so that is now good. Flashed back the original nand and completly removed the CR. - Still 0022. I see the PLL point is ripped from the board. I checked the alt point resistor right next to it and it reads 9.98K Ohm.

Anyone got any ideas on where I should be looking to correct the RR and get this console atleast booting stock again.

 

[slipcky6]

Well from what I know a 0022 error means a bad flash. Did you remove all the wires from the CR and then flash to stock and try to boot?

 

[mm53668]

Flashed back the original nand and completly removed the CR. - Still 0022. .

Please see above

 

[slipcky6]

Did you just take the wires off the CR board and the actual moon? Sorry that's what I meant to ask.

---------- Post added at 17:04 ---------- Previous post was at 17:01 ----------

Also check here:
http://xbox-experts.com/errorcode/E10/0022/

 

[mm53668]

no wires or CR is attached to the console. = Completly removed. It is flashed back to original nand

 

[slipcky6]

Is there any visible solder bridges?

 

[Krafter]

How long does it take to get the 0022?

5s- issue with CPU_RST/CPU_PLL_BYPASS
15s - LDV
30s - GPU issue.

 

[KhaineGB]

If the PLL point is completely removed from the board, you may need to do the trace fix.

Should be a thread about that on the boards.

 

[mm53668]

How long does it take to get the 0022?

I'll have to check that I know its between 15-30 seconds

 

[paul.86]

Ldv value is incorrect if it takes 20 seconds to show

---------- Post added at 03:22 ---------- Previous post was at 03:20 ----------

If you cannot boot xell to determine ldv value then get your orig nand check ldv value and rebuild retail add one more f so if its 5 make sure you put ffffff in options.ini

 

[oveis]

how it can be about changing his ldv , when he never boot to xell or update his dash ?

 

[Martin C]

Repair CPU PLL bypass.

 

[oveis]

martin are you think in this case he bridge pll bypass or he damaged it ?

 

[Martin C]

If CPU PLL has been ripped, you'll still get 10k from the resistor but no connection to the CPU. Therefore after 5-6 seconds it'll 0022

 

[oveis]

If CPU PLL has been ripped, you'll still get 10k from the resistor but no connection to the CPU. Therefore after 5-6 seconds it'll 0022

so should use alternative points to figure that rrod ?

 

[x23are]

martin what is the cpu_PLL_Bypass problem(0022 in 5-6 sec)?

 

[cskalash]

If you blown the pll_bypass you need to rebuild that track again.
See this post:
http://www.team-xecuter.com/forums/showthread.php?t=74992
You need to re-connect that resistor to its track. That is just for repairing the problem. Then you need to make a new pll_bypass. You can choose the resistor's side, the motherboard upper side point, and just remove some plastic from the wire and solder it like in the middle of the wire or so. If you can solder 2 wires in the resistor that would be perfect. One goes for upper side of the board, and the other goes for CoolRunner.

 

[mm53668]

Repair CPU PLL bypass.

Thanks repaired the cpu PLL and it boots right up - all glitched and ready to go. Guess I was seeing the images as two alt points rather than a reroute of the PLL

 

[x23are]

my nand not detected but it have orig nand.
the problem is 0022 in 5-6sec.
do it repair whit ubers tutotial ?(with org nand)

 

[paul.86]

Change ldv value in multibuilder

Sent from my HTC Vision using Tapatalk