Falcon not booting into xell

[Luffe]

Console Type: Falcon
NAND size: 16
Dashboard version: 2.0.<
CB version: 5771
RATER OUTPUT

[B][B][B][B][B][B][B][B][B][B][B][B][B][B][B]Phat Selected
[/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B]Version: 10
Power Up
Waiting for POST to change
Post 24 - VERIFY_OFFSET_3BL_CC 
Post 2C - SHA_COMPUTE_3BL_CC 
Post 28 - FETCH_CONTENTS_3BL_CC 
Post 08 
Post 28 - FETCH_CONTENTS_3BL_CC 
Post 08 
Post 28 - FETCH_CONTENTS_3BL_CC 
Post 08 
Post 48 - SHA_COMPUTE 
Post 08 
Post 48 - SHA_COMPUTE 
Post 08 
Post 28 - FETCH_CONTENTS_3BL_CC 
Post 08 
Post 28 - FETCH_CONTENTS_3BL_CC 
Post 08 
Post 28 - FETCH_CONTENTS_3BL_CC 
Post 08 
Post 48 - SHA_COMPUTE 
Post 08 
Post C8 - SHA_VERIFY 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 60 - INIT_KERNEL 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Post 18 - FETCH_CONTENTS 
Post 19 - HMACSHA_COMPUTE 
Post 1A - RC4_INITIALIZE 
Post 1B - RC4_DECRYPT 
Post 1C - SHA_COMPUTE 
Post 1D - SIG_VERIFY 
Post 1E - BRANCH 
Post 20 - CB entry point reached 
Post 21 - INIT_SECOTP 
Post A0 - Panic - VERIFY_SECOTP_6 
Post 10 - Payload/1BL started 
Post 11 - FSB_CONFIG_PHY_CONTROL 
Post 12 - FSB_CONFIG_RX_STATE 
Post 13 - FSB_CONFIG_TX_STATE 
Post 14 - FSB_CONFIG_TX_CREDITS 
Post 15 - FETCH_OFFSET 
Post 16 - FETCH_HEADER 
Most Fails(cumulative): 0xA0
Shutdown
[B][B][B][B][B][B][B][B][B][B][B][B][B][B][B]Resetting................[/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B][/B]

Description of problem:
1: I have wired everything up
2: Got 4 nand that match
4: Create/Write xell
3: I cant boot into xell, the green led keeps flashing
4: Tried different dips, with and without AUD_CLAMP, different volt.
5: A little bit frustrated - so i hope you guys can help

I have used both hdmi and av.

Was the console working before you started:
Yes. I have also tried the orignal nand - everything works as expected.

 

[scott1503]

Dash needs to be a minimum of 15574 restore original nand update console and then start the rjtag process again from the start
or rgh1 the console as 12416 is fine for rgh1

 

[skillet34]

R-jtag is for 15574 and above with split CB 9199 with CB of 5771 would be rgh1
http://team-xecuter.com/forums/showthread.php/78885-RGH-roadmap-for-n00bies

EDIT: scott beat me

 

[Luffe]

Thanks guys

I got it working. This was a really stupid mistake and really appreciate that you didn't answer back with some bs comment.