RGH Falcon RGH Troubles

2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
I have here a clients Falcon 360. I have done lots of slims and phats and had never this problem before.

The coolrunner doesn't seem to try to glitch as the debug led never blinks...

I have checked my wiring multiple times, and have resoldered them on like 3 times... I tried another coolrunner and reflashing it with a jtag cable instead of my nandx.... Jrunner found everything fine, and built the .ecc fine multiple times as well. I tryed reflashing stock and it booted fine.

I just can't seem to get this thing to glitch.

Below I have posted pics and I hope it was something silly lol :facepalm:

Edit: No luck with HDMI either

Here is an extra pic


BTW: I have looked at all the point under a microscope and all seem fine with no bridges or shorts....
 
Last edited:
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
BL4K3Y said:
I notice the console switch is set to SLIM, was this for testing purposes?

Also, what's the CB version of this console?
Click to expand...

CB: 5771, should be fine

Switch hasn't made a difference
 
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
BL4K3Y said:
Can you re-program your CoolRunner using J-Runner (or NandPro) and paste the log here please.
Click to expand...
Sure

Here: \\




Checking Files
Finished Checking Files
Programming Coolrunner
Flashing C:\Users\Christian\Desktop\Xbox\J-Runner v01 Beta (256)\common\xsvf\falcon.xsvf to CoolRunner
Input Filesize: 593E
Output Filesize: 2832
Done!


Exited!
 
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
BL4K3Y said:
The only other suggestion I have left is to try moving the wires around (away from the coils under-side).
Click to expand...
Damn, I already tried that, even used the alternate CPU_RST...
 
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
I'm assuming when you write the original 50 blocks back it boots ok?

CPU_PLL_BYPASS is normally the culprit, so double-check this wire.
 
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
Martin C said:
I'm assuming when you write the original 50 blocks back it boots ok?

CPU_PLL_BYPASS is normally the culprit, so double-check this wire.
Click to expand...
Yes, stock Nand works fine.. The CPU_PLL isnt bridged or touching anything.. anything else I can do?
 
ball00

ball00

VIP Member
Nov 8, 2011
632
0
France
Have you checked soldering with a multimeter? Are you sure the coolrunners were programmed correctly?
 
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
KhaineGB said:
This might be a long shot... but...

Are you sure that coolrunner isn't a clone??? It looks suspect to me.
Click to expand...
I bought them both from Xconsoles so no.

ball00 said:
Have you checked soldering with a multimeter? Are you sure the coolrunners were programmed correctly?
Click to expand...
They have been programmed via nandx in jrunner and impact via Jtag cable

mattc141 said:
It also may be a long shot but you could just take everything off the board and completely restart from scratch???

Other than that and what has already been said im not sure...
Click to expand...
I will try to redo it with new cable..
 
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
BL4K3Y said:
Are you absolutely certain that this is a Falcon console and not a Zephyr?
Click to expand...
Yes, The power supply is a falcon port and nand is falcon too
 
axee44

axee44

VIP Member
Nov 8, 2011
330
48
York,UK
Have you done continuity test between xbox motherboard and coolrunner??
 
2

2615863

VIP Member
Nov 30, 2011
552
33
Tampa,FL
axee44 said:
Have you done continuity test between xbox motherboard and coolrunner??
Click to expand...
Yes, all the points beep and are connected
 
You must log in or register to reply here.