RGH Falcon v3 boot not Xell

[andi_a11]

I try2 days :facepalm:RGH2 boot on my Falcon v3. Xell not possible with Shielded cable and standard cable + 3,3k ,470pF
Hardware J-R v2 and CoolRunner Rev.C
Dashboard 16202
CB_A 5774
CoolRunner read with B,C,D ,Falcon-rgh2 not Boot Xell
Read Nand no problem no ERROR


Programming Coolrunner
C:\Users\andi_a11\Desktop\J-Runner v3 (5) Core Pack\common\xsvf\TX_RGH2_B.xsvf
USB XSVF Player Initialized
Xilinx XC2C64A-VQ44 ......... [DETECTED]
Erase Succeeded
File: C:\Users\andi_a11\Desktop\J-Runner v3 (5) Core Pack\common\xsvf\TX_RGH2_B.xsvf
Sending Out Packets .........
Success
Falcon Manually Selected
ECC created
Version: 10
Flash Config: 0x01198010
Writing Nand
image_00000000.ecc
Done!
in 0:19 min:sec


Please help

 

[skillet34]

Do you have any pics of the STBY-CLK or CPU RST points? Do you have a green led blink every five seconds or so? Need a little more info.

 

[andi_a11]

yes green led blink every five seconds and 30 min. long not xell

 

[GeekHeat]

Try switching it to slim. See if that makes a difference. If not, keep it on slim and remove C8 resistor.

 

[andi_a11]

switching Phat to Slim not better by Coolrunner D Phat green led Off switch to Slim green blink every five seconds

C8 on board remove only JP and 3-2 ​and bridge 2-1

 

[RayBray]

Rev D is a fake. you got ripped off. you should get a proper TX product for support.

 

[andi_a11]

My product ist TX CoolRunner rev.C on Xbox 360 board can be seen on photo

 

[andi_a11]

Coolrunner D sorry my mistake

 

[Krafter]

Coolrunner D sorry my mistake

There isn't a such thing as a rev D. Anything that's says Rev D is a fake and not made by TX. Fakes are not supported here either.

Edit: sorry. I see in your first set of images, you do have a Rev C. I think we just have a slight language barrier which makes things a little confusing.

 

[john mathews]

u need to remove the resister and cap/ your soldering is bad and needs to be cleaned up and use flux

 

[andi_a11]

Measure resistance of R4B24 33 ohms

 

[andi_a11]

u need to remove the resister and cap/ your soldering is bad and needs to be cleaned up and use flux

Ok remove resister and cap may soldering bad ? wath exactly , use flux Amtech rma-223 no clean and X-M3 cleaner

 

[andi_a11]

after removing cap and resister not better no xell
other ideas ?
remove C8 resistor on coolrunner for slim ?

 

[The Result]

Yes I have the best advice quite wasting your time with a falcon RGH2 and buy a CR4 or send this to someone.

 

[ultimate360]

No, he is not wasting time for falcon rgh2, I have a configuration that works fantastic every time. Here it is:


Timing file RGH2 B

Switch to slim

Remove c8

Bridge either 2-3 or 1-2, see which one works better (typically 1-2 is better)

Use full length slim blue reset wire and solder it to the point on board, then run it around the front of the heatsinks. Coil the slack over the southbrige chip and connect to coolrunner.

Do that, and see what happens

 

[andi_a11]

No, he is not wasting time for falcon rgh2, I have a configuration that works fantastic every time. Here it is:


Timing file RGH2 B

Switch to slim

Remove c8

Bridge either 2-3 or 1-2, see which one works better (typically 1-2 is better)

Use full length slim blue reset wire and solder it to the point on board, then run it around the front of the heatsinks. Coil the slack over the southbrige chip and connect to coolrunner.

Do that, and see what happens

Yes Xell Loading good answer Ultimate360 Thanks :wink:

 

[ultimate360]

Told ya

 

[The Result]

Huh proved me wrong nice one I may have to try it I have a couple rev c unopened may have to try this.