falcon wont boot xell

[XxGLITCH3RSxX]

hi guys before i start i have made many r-jtags with boot time within perfecto on j-runner

i installed the r-jtag the glitch led (green) was not flashing properly so i touch up my soldering on the post_out qsb and it is glitching proberly now
i am using the r-jtag starter so on the top side of the board is the wire install
i use the switching diodes.
i could not get a good pic of the post qsb of lighing ect but i can say all points are fine and got a good connection

Console Type: (Falcon/Opus)
NAND size: 16
Dashboard version: e.g 2.0.15574
CB version: e.g 5774

Phat SelectedVersion: 10
Power Up
Waiting for POST to change
Post 80
Post 60 - INIT_KERNEL
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 30 - VERIFY_OFFSET_4BL_CD
Post 20 - CB entry point reached
Post 30 - VERIFY_OFFSET_4BL_CD
Post 70 - INIT_VIDEO_DRIVER
Post 60 - INIT_KERNEL
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 60 - INIT_KERNEL
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Post 10 - Payload/1BL started
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 60 - INIT_KERNEL
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 10 - Payload/1BL started
Post 11 - FSB_CONFIG_PHY_CONTROL
Post 18 - FETCH_CONTENTS
Post 19 - HMACSHA_COMPUTE
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Post 60 - INIT_KERNEL
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 10 - Payload/1BL started
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 10 - Payload/1BL started
Post 11 - FSB_CONFIG_PHY_CONTROL
Post 15 - FETCH_OFFSET
Post 18 - FETCH_CONTENTS
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Post 30 - VERIFY_OFFSET_4BL_CD
Post 10 - Payload/1BL started
Post 20 - CB entry point reached
Post 40 - Entrypoint of CD reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 10 - Payload/1BL started
Post 11 - FSB_CONFIG_PHY_CONTROL
Post 18 - FETCH_CONTENTS
Post 19 - HMACSHA_COMPUTE
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 60 - INIT_KERNEL
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 30 - VERIFY_OFFSET_4BL_CD
Post 30 - VERIFY_OFFSET_4BL_CD
Post 20 - CB entry point reached
Post 20 - CB entry point reached
Post 11 - FSB_CONFIG_PHY_CONTROL
Post 12 - FSB_CONFIG_RX_STATE
Post 19 - HMACSHA_COMPUTE
Post 1A - RC4_INITIALIZE
Post 1B - RC4_DECRYPT
Post 1C - SHA_COMPUTE
Post 1D - SIG_VERIFY
Post 1E - BRANCH
Post 20 - CB entry point reached
Post 21 - INIT_SECOTP
Post A0 - Panic - VERIFY_SECOTP_6
Most Fails(cumulative): 0xA0
Shutdown

0
3


Overall: 1 / 20
Average: 3.00
Median: 3
Score: 6.00


Cycle 3 - 100.00%


100% within 3 Cycles




Was the console working before you started: Y




can i more pics but i carnt get a good pic of the post_OUT QSB BUT WILL add a pic if you really want but you carnt see anything

i dont have post log but will add if needed

wondering if anyone can help

thanks

XxGLITCH3RSxX

 

[Martin C]

[h=3]*** R-JTAG SUPPORT TEMPLATE - READ AND FOLLOW THIS BEFORE ASKING FOR ANY SUPPORT ***[/h]

 

[XxGLITCH3RSxX]

*** R-JTAG SUPPORT TEMPLATE - READ AND FOLLOW THIS BEFORE ASKING FOR ANY SUPPORT ***

ok done it i dont have a rater i will do it asap

 

[xzanox]

And i think you will have to post a few more pictures of the qsb's.

 

[Martin C]

So no JR-Pv2 ? What help do you expect to get without posting your POST monitor output?

 

[XxGLITCH3RSxX]

So no JR-Pv2 ? What help do you expect to get without posting your POST monitor output?

ok i updated it it has the post/rater

 

[Martin C]

Where's your J-Runner screenshot?

Have you tried all 18 combinations before asking for help?

 

[XxGLITCH3RSxX]

Where's your J-Runner screenshot?

Have you tried all 18 combinations before asking for help?

ah sorry forgot to add the screen shot

what 18 combinations never herd of them before

 

[Martin C]

ah sorry forgot to add the screen shot

what 18 combinations never herd of them before

If you read the installation guide, you have read them.

There are 6 DIPs to choose from with 3 different power options.

6 multiplied by 3 is 18.

Before even asking for help, all combinations should be tested.

 

[XxGLITCH3RSxX]

If you read the installation guide, you have read them.

There are 6 DIPs to choose from with 3 different power options.

6 multiplied by 3 is 18.

Before even asking for help, all combinations should be tested.

yes i read the install forms and yes i have use the dipped settings all them

 

[Martin C]

yes i read the install forms and yes i have use the dipped settings all them

You've not tried all 3 power settings. You're making this very hard work.

 

[XxGLITCH3RSxX]

You've not tried all 3 power settings. You're making this very hard work.

i am sorry do you mean the dipped setting or volts settings if you could just explain a little more i will be able to work better with your instructions

thanks for your help

 

[Martin C]

You have three power settings: default, 1v2 and 1v8 (as per the guide).

So leave at default and try to boot the console using DIPs 1 to 6, one at a time for about 5 cycles each.

Next change the power setting to 1v2 and do the same again.

Finally change to 1v8 and do the same again.

That's 18 combinations.

 

[XxGLITCH3RSxX]

You have three power settings: default, 1v2 and 1v8 (as per the guide).

So leave at default and try to boot the console using DIPs 1 to 6, one at a time for about 5 cycles each.

Next change the power setting to 1v2 and do the same again.

Finally change to 1v8 and do the same again.

That's 18 combinations.

hey mate got it sorted thanks for your time and help thank you

 

[Martin C]

For others, can you please state what worked?

 

[XxGLITCH3RSxX]

For others, can you please state what worked?

yes if was default voltage 2 and 7 and it boots great