RGH Fans Went Crazy 12v

[thebomber]

hey guys so i was rgh a BB Jasper, got the key off it, and then returned the original nand, everything was great closed the console and screws etc.. went to try it again its all crazy

its a 512mb nand which took me like 3 hours to read and 2 more to write, :biggrin: i just knew i only needed the first 64mb:facepalm:,

anyway i wish someone could help me out here

that happned before to my jasper and some dude connected the fans to a steady 5v from the dvd drive, but cant remember how to do it:rolleyes2:

 

[keil423]

Does it only do it when your on freestyle dash? You can adjust the fan speeds in freestyle

 

[thebomber]

no i only installed xell to get the dvd key for some guy, and flashed the original image back,

tried the console for a few min, was normal

placed it in the cage and it went crazy,

took it out still crazy

flashed the original twice still crazy

there are no bad blocks at all with my 3 dumps

just 3 differences were there anazlyed it using nand healer said no bad blocks

dont know

now im trying to read the nand again i get problem reading 2 blocks

may this be the problem

Fixing ECC blocks
Step 1 of 2: Reading nand1_0160.bin.............Read error(1), retrying....
Step 1 of 2: Reading nand1_0160.bin.............Read error(2), retrying....
Step 1 of 2: Reading nand1_0160.bin.............Read error(3), skipping block.
Step 2 of 2: Reading nand1_0398.bin.............Read error(1), retrying....
Step 2 of 2: Reading nand1_0398.bin.............Read error(2), retrying....
Step 2 of 2: Reading nand1_0398.bin.............Read error(3), skipping block.

i wish someone would gide me to using the power from the dvd drive cable

i forgot how it was done

 

[keil423]

DVD drive is still 12 volts. Plus you should stay away from the drive. Steal power elsewhere.

 

[Dosk3n]

I steal power from the DVD drive on fan mods and never had an issue with it to be fair. Thats just my experience though.

However mate it could just be as simple as its over heating. Ive spoke to a few people having this problem and its because when theyre lifting the motherboard out theyre holding on to the heatsink and breaking the seal of thermal paste. Try taking heatsink off and adding better thermal paste incase youve broke the paste thats on there since the rubbish they use can crack.

 

[thebomber]

Its not overheatin since i press on i hear 12 v anyway someone made it for me before he stole 5 v from the dvd drive and it was working on 5 if there is anything lower than 12 thats one noisy jasper.

Or if i can take 5 v from the mobo which cables should i connect etcc

 

[esbmaepo]

Its not overheatin since i press on i hear 12 v anyway someone made it for me before he stole 5 v from the dvd drive and it was working on 5 if there is anything lower than 12 thats one noisy jasper.

Or if i can take 5 v from the mobo which cables should i connect etcc

Will your system still be able to control fan speed if you take power from elsewhere? Will fans not always spin at same speed?

Do fans go crazy as soon as you turn on console or does it take a while?

 

[thebomber]

as soon as i turn it on, it goes 12v

thats why im sure its not overheating, and happened to my console before

but this dude was working fine, i just closed it and its gone crazy, hahhaha so weird

 

[Martin C]

The worst part of all this is you only needed to write back the 50 blocks that the ecc occupied to return it to stock.

nandpro usb: -w64 nand.bin 0 50.

Fans go crazy if your config block is wrong. I suggest you run your NAND dump through multi_builder and make a new one. Flash xell back to the console and write your new retail nand using rawflash.

 

[thebomber]

ok will try it later martin thx for the hint