F'd up cool runner pads (noob)

X

xboxnick360

Full Member
Nov 8, 2011
65
6
So this is what we're lookin at today



im using the power from the xbox and found the tck,tmi, and tms trace lines on the back.I soldered to them and I had an Ohm reading from all connections to the ground on the other side of the cool runner.used a magnifying glass to make sure no solder connection was on more than 1 trace.

after that i quickly hot glue guned everything

I have a Green and Red light showing up on the cool runner . when i attempt to program it i get this error message when trying to initialize to chain.



im also using this lpt schematic and i am well aware that this could very well be the problem
 
Last edited:
X

xboxnick360

Full Member
Nov 8, 2011
65
6
Error when initializing chain

Error impact.. a problem may exist in the hardwarr configuration. Check that the cable, scan chain, and power connections are intact, that the spe ified scan chan configuration matches the hardware and that the power supply is adequate and delivering the correct voltage.
 
X

xboxnick360

Full Member
Nov 8, 2011
65
6
damnt, i think that schematic is for another chip completely... f**kin brother really needs to learn how to read
 
B

bonovox

Full Member
Mar 28, 2006
59
0
xboxnick360 said:
So this is what we're lookin at today



im using the power from the xbox and found the tck,tmi, and tms trace lines on the back.I soldered to them and I had an Ohm reading from all connections to the ground on the other side of the cool runner.used a magnifying glass to make sure no solder connection was on more than 1 trace.

after that i quickly hot glue guned everything

I have a Green and Red light showing up on the cool runner . when i attempt to program it i get this error message when trying to initialize to chain.



im also using this lpt schematic and i am well aware that this could very well be the problemLink To Image
Click to expand...
Yep all looks good and should work. Can't for the life of me figure out what could be wrong. This should be stickied!
 
keil423

keil423

VIP Member
Apr 4, 2011
1,954
88
South Dakota, USA
www.epicconsole.com
Hot glue tip. When you apply hot glue just apply a small amount. You need just enough to go from one side of the wire to the other. Immediately after applieing the Hot glue lick the tip of you fingure just enough to get it wet and then rub the hot glue smooth and press the edges down to the board a little. You will get much cleaner looking results. much the same as you do when applieing caulk ya know.

If you dont want to lick your fingure you can just use water!
 
xbox360 hacker

xbox360 hacker

BANNED
Feb 28, 2011
1,405
0
united kingdom
xboxnick360 said:
So this is what we're lookin at today



im using the power from the xbox and found the tck,tmi, and tms trace lines on the back.I soldered to them and I had an Ohm reading from all connections to the ground on the other side of the cool runner.used a magnifying glass to make sure no solder connection was on more than 1 trace.

after that i quickly hot glue guned everything

I have a Green and Red light showing up on the cool runner . when i attempt to program it i get this error message when trying to initialize to chain.



im also using this lpt schematic and i am well aware that this could very well be the problemLink To Image
Click to expand...
After seeing your bodge job it reminded me why i am waiting for my Xecuter NAND-X To CoolRunner JTAG Cable. hope you get it sorted :)
 
M

MegaLiftman

VIP Member
Apr 13, 2011
194
0
Concrete Jungle
I will give you top marks for persistance but zero for skill.

If my 5 year old did that i would give her a bollocking.
 
F

frazzeld

VIP Member
Jun 21, 2007
1,670
0
UK
You need to do three things

1/ Buy a new coolrunner
2/ install it correctly http://www.team-xecuter.com/forums/showthread.php?t=75450
3/ Send your knackerd coolrunner to this fella

[ame="http://www.youtube.com/watch?v=I7TK_8RiVj8&feature=player_embedded#"]Will It Blend? - Justin Bieber - YouTube[/ame]
 
You must log in or register to reply here.