first time rgh.. please help!

Status
Not open for further replies.
G

Garv4322

Junior Member
Aug 21, 2009
10
1
ENGLAND
hi i'm wondering if anyone could point me in the right direction.. i have installed all the wires and have good strong solder joints and i have dumped my nand with the JR Programmer V2.. i have installed the Coolrunner Rev C too with no issues.. everything has gone fine up to creating the ECC* .. now it says i have created it with success and then the write ECC goes fine too.. also so does the programming .. everything say's success ... now i did a lot of digging and found another program to try and create the ECC* called (360 Multi Builder) i loaded up my nand dump in there and got this message:

Checking the file nanddump.bin, Please wait...


* found flash image, unpacking...
ECC'ed - will unecc.
Found 2BL (build 5774) at 00008000


[CB] version [5774] found !!


This CB version is not compatible with the Glitch Hack currently...


The Xell/ECC image won't be created




Press any key to continue . . .


is there no way at all of glitching this console now with this CB 5774 or is there a work around....?

any help would be gratefully appreciated .. Many thx ;)
 
G

gavin_darkglide

VIP Member
Dec 14, 2012
2,303
118
First off use j-runner. Second off Krafter is correct, now when you create ecc, it injects the keyvault from your nand dump into a premade ecc. If I remember correctly cb 5774 is a falcon RGH2. Falcon RGH2 is extreemly hard to get to glitch consistantly. pictures and j-runner log would be helpful. Please fill out the RGH template before asking for more help.
 
  • Like
Reactions: Garv4322
G

Garv4322

Junior Member
Aug 21, 2009
10
1
ENGLAND
Template:

Products: J-R Programmer V2 and CR3 Rev C
Console type: Falcon
Nand size: is there a size for falcon?
Dashboard version: 16537
CB version: 5774
Screenshot of NAND details from J-Runner:
http://imageshack.com/a/img820/7561/vnjn.png
-----------------------------------------------------------------------------------------------

J-Runner log:
===================================================
21 June 2014 10:42:47

J-Runner v0.3 Beta (4) Started

Checking Files
Finished Checking Files
Falcon Manually Selected
Version: 10
Flash Config: 0x01198010
01198010
Xenon, Zephyr, Opus, Falcon
CB Version: 5774
Falcon/Opus
Reading Nand to C:\Users\Heather&Paul\Desktop\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 3:22 min:sec

Reading Nand to C:\Users\Heather&Paul\Desktop\J-Runner v02 Beta (284) Core Pack\J-Runner v02 Beta (284) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Falcon/Opus
Jtag Selected
Nand Initialization Finished
Reading Nand
Done!
in 3:22 min:sec

Comparing...
Nands are the same
-------------------------------------------------------------------------------------------------------

Image of Coolrunner:
http://imageshack.com/a/img837/6048/fu2k.jpg
-----------------------------------------------------------

Images of close-up soldering to motherboard:
http://imageshack.com/a/img822/344/fq7z.jpg
http://imageshack.com/a/img829/9325/t9ed.jpg
http://imageshack.com/a/img856/5571/b4qk.jpg
http://imageshack.com/a/img842/3812/rcnqq.jpg
-------------------------------------------------------------------------------------------------------



Description of problem: Can’t seem to get past the create ECC.. the CB is 5774 .. I’m told I have to flash a prebuilt one ( not sure how to do that)

Was the console working before you started: Y

Do you get a green debug light appear on the RGH chip every 4-5 seconds: Y

How long is the light on for each time: 2-3 seconds


i think that is everything! :)
 
S

seniorcelica

Senior Member
Apr 5, 2012
127
0
dont select jtag select rgh2. and not to be a d!ck but that soldering could be cleaned up or practice some more.
 
Last edited:
G

Garv4322

Junior Member
Aug 21, 2009
10
1
ENGLAND
seniorcelica said:
dont select jtag select rgh2. and not to be a d!ck but that soldering could be cleaned up or practice some more.
Click to expand...
i didn't select jtag.. it was on that after reading my nand , as for soldering,, i'm getting better and better, as i said this is my 1st attempt ;)
also i have tried selecting RGG2 also .. programming the cr3 .. and still no joy :/



Game_Over said:
Part of the problem is the FAKE CR. Where did you buy it?
Click to expand...
i bought it off amazon m8!
 
Last edited:
Status
Not open for further replies.