Fix RDoD

C

Chris28

Junior Member
Feb 25, 2012
21
0
Croatia
I have XBox360 Slim which worked fine until I decided to update dashboard from 13146 to 13599.
I forgot to flash to stock before I tried to update (it was on LT 9504, don't remember which LT version). I also soldered Sputnik360 on my pcb with MXIC IC before updating.
Then of course I got error, something like this xxx-xxxx-xxxx-xxxx-C000-0001. I just needed to flash to stock.
But at that time I tought Sputnik was the problem so I tried to unsolder it and failed. I ruined the PCB.
So I bought another PCB with Winbond IC. I successfully did Kamikaze hack and flashed it to stock 9504 and got red dot of death. Also tried 2702 but nothing. I tried to turn on XBox without DVD drive, but still RDoD so DVD drive is not the problem, nor PCB. Secondary error is 1023.
I got suggestion that I should try to do RGH on my Slim and see if that fixes the problem.
I bought JR-Programmer and Coolrunner rev.C with some QSB's. Should I just follow normal procedure for RGH or do something different? Do you think RGH will fix RDoD?
 
C

Chris28

Junior Member
Feb 25, 2012
21
0
Croatia
@jimlfixit I flashed it a thousand times it's always the same. I used to get error, now I get RROD. XBox should turn on without DVD drive, mine just gets RROD again.

@Turdfurgeson82 Of course I did. I figured if it's red dot of it should be RDOD. Doesn't matter anyway.
 
P

PersonCC

Senior Member
Apr 14, 2012
122
0
After you get a good firmware flash to the drive.

You may want to try holding the SYnc button on power up. It will clear any failed dash updates.




(Secondary Error 1023 is E75.... Network chip cold joint/ wrong vendor. It seems to be DVD Drive Related
Source: http://xbox-experts.com/errorcode/E75/1023/)
 
Last edited:
C

Chris28

Junior Member
Feb 25, 2012
21
0
Croatia
Maybe I should do a nand read and see how it goes. And then maybe continue with rgh.
 
Last edited:
C

Chris28

Junior Member
Feb 25, 2012
21
0
Croatia
I dumped 2 nands, compared, everything fine.
Flashed Coolrunner. Created ECC. Wrote ECC. Booted into Xell and got CPU key. Pasted it to JRunner and now I need help.
Also I checked for bad blocks, it says this :(:

• Bad Block ID @ 0x399 [Offset: 0xED7200]

• Bad Block ID @ 0x399 Found @ 0x3FF[Offset: 0x107BE00]

Should I continue? I don't know which dash version should I choose, and how should I set up Launch.ini. I know it's personal preference, but don't know which option is for what?
I chose RGH, not RGH2. I don't even know the difference.
 
Last edited:
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
• Bad Block ID @ 0x399 Found @ 0x3FF[Offset: 0x107BE00]

It's telling you right there that the bad block has been remapped to 0x3FF.

Why doesn't anyone read up on bad blocks - you can google it! You get this page:

http://free60.org/NAND:Bad_Blocks

Take a read. FTR, J-Runner deals with it all for you.
 
C

Chris28

Junior Member
Feb 25, 2012
21
0
Croatia
I finished. But still getting RDOD. I guess RGH can't fix this and I don't know why it keeps getting RROD. Maybe because od wireless adapter (secondary error 1023), but if I remove it I will get E75 error of course. I should try with another one but I don't have money to buy it and then see that isn't the problem in the end. It's gambling.
 
Last edited:
TilVl

TilVl

VIP Member
May 11, 2011
1,383
0
The 360 slim should work fine with out wireless adapter. I ran my old 4gb with out the wireless cause it was never in the case.

Sent from my SGH-T839 using Tapatalk
 
C

Chris28

Junior Member
Feb 25, 2012
21
0
Croatia
Than maybe ethernet chip is the problem. I already checked the continuity on sata pins and cables, and it should boot without the DVD drive anyway. I don't see what else could be the problem except ethernet chip.
 
Last edited:
You must log in or register to reply here.