Flash Config: 0x00000000

[cadebenoit49]

Hi, my name is Cade and I want to RGH2 my Xbox 360 Slim Trinity. I've already soldered everything. When I open J-Runner to Create and Write the ECC, it gives me this error:

"Version: 10Flash Config: 0x00000000
Can not Continue"

A solution of my problem would be amazing. Thank you for taking your time to read my problem.

~Cade

 

[Dadko]

Did you connected power supply? Also check soldering.

 

[cadebenoit49]

Yes, I did and every solder point seems fine.

 

[GeekHeat]

Makes sure everything is plugged in properly and no wires have come loose.

 

[cadebenoit49]

What all needs to be plugged in? I have the J-R Programmer wire soldered onto my motherboard, and the other end of that wire is in my J-R Programmer and I have the USB plugged into the J-R Programmer and the other end of the USB into my computer. Is that it?

 

[GeekHeat]

What all needs to be plugged in? I have the J-R Programmer wire soldered onto my motherboard, and the other end of that wire is in my J-R Programmer and I have the USB plugged into the J-R Programmer and the other end of the USB into my computer. Is that it?

yes thats it. Just saying make sure the wires are ok or the white plastic connecter is plugged in the right way up or in properly. Try another USB port.etc.

Did u read the nand ok with 2 matching dumps.

 

[cadebenoit49]

Yea, I read it just fine.

 

[GeekHeat]

Does the console still boot to dash ok if u switch the coolrunner switch to program.

 

[cadebenoit49]

Yes, it boots to dash fine, I'm supposed to switch the CoolRunner to Program? Even though I am Writing the ECC?

 

[GeekHeat]

Switching the coolrunner to program also turns off the power to the chip so that it will boot the stock dash ok.

Let's see some pics of install.

 

[cadebenoit49]

Oh okay, yea the dash is all good, What do I do now?

 

[cadebenoit49]

Here are pics that I have taken with my phone:
http://s1281.photobucket.com/user/cadebenoit49/media/IMG_1183_zpsv8chy4ct.png.html?sort=3&o=0
http://s1281.photobucket.com/user/cadebenoit49/media/IMG_1182_zps3olpjezh.jpg.html?sort=3&o=1
http://s1281.photobucket.com/user/cadebenoit49/media/IMG_1181_zpsztc5hnsx.jpg.html?sort=3&o=2
http://s1281.photobucket.com/user/cadebenoit49/media/IMG_1180_zpsecyjcex6.jpg.html?sort=3&o=3
http://s1281.photobucket.com/user/cadebenoit49/media/IMG_1174_zps8pxwgk1l.jpg.html?sort=3&o=4
http://s1281.photobucket.com/user/cadebenoit49/media/IMG_1173_zpsbhplhfwa.jpg.html?sort=3&o=5
http://s1281.photobucket.com/user/cadebenoit49/media/IMG_1172_zpsmujuwpyx.jpg.html?sort=3&o=6

 

[cadebenoit49]

Any of these pics might help?

 

[Dadko]

I would say, that it is soldering problem. Try to clean that and start again. Don't forget flux.

 

[Mikaz]

Looks like bad soldering. Metal ends of wires should be at least 3 times shorter.

 

[cadebenoit49]

Alright thanks, I'll let you know if it works or not. One sec.

 

[cadebenoit49]

I cut them shorter... still not working. :'(

 

[cadebenoit49]

Anything else that might help? I'm super frustrated.

 

[15432]

damaged 'B' point on the mobo

 

[Tenuous]

has anyone else noticed its a fake coolrunner ?