No, probe v3 does not need to be used. Assuming you are using at usbpro you should be experiencing no problem. Select usbpro port, intro drive, erase, load source-orig, load target-whatever drive lt fw, spoof source to target, write, and lock drive. Prior to all of this make sure your drive is unlocked.
LITEON DG-16D4S - SLIM Flashed TX Unlocked PCB v1.1, Now constant 0x80
- Thread starter KiiNGxDruMMeR
- Start date
jsinger47
Troll Eating Dogs
You merely need to probe MPX01 with ground.
So a wire to any ground will suffice. For example, the case of your xbox (while its plugged in, of course).
There are lots of options there, so use your imagination.
Like I said in my previous posts, I have tried to intro but it says 0x80 no drive detected
Great... this is my 2nd PCB in a month
---------- Post added at 16:41 ---------- Previous post was at 16:40 ----------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.92 Beta (304)
Session Started Tue Sep 04 16:37:02 2012
This is a 32 bit process running on 2 x 32 bit CPUs
X360USB PRO detected, Version 0.18
Found 1 I/O Ports.
Found 1 Com Ports.
Found 8 windows drives C: D: E: F: G: H: I: K:
Found 2 CD/DVD drives E: F:
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro:
................................................................................................................................................................................................................................................................................................................................
Aborted by User!
Sending Lite-On-Erase request to port 0x0000
..............
Drive returned Status 0x80
....................
Device Intro failed!
---------- Post added at 16:41 ---------- Previous post was at 16:40 ----------
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.92 Beta (304)
Session Started Tue Sep 04 16:37:02 2012
This is a 32 bit process running on 2 x 32 bit CPUs
X360USB PRO detected, Version 0.18
Found 1 I/O Ports.
Found 1 Com Ports.
Found 8 windows drives C: D: E: F: G: H: I: K:
Found 2 CD/DVD drives E: F:
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro:
................................................................................................................................................................................................................................................................................................................................
Aborted by User!
Sending Lite-On-Erase request to port 0x0000
..............
Drive returned Status 0x80
....................
Device Intro failed!
if thats the case then i think its a user error and not faulty hardware unless you just been unlucky
Last edited:
RhoTrux64
VIP Member
- Jun 22, 2004
- 591
- 0
Dicko316
VIP Member
V1.1's have an external switch mate
OP i think where your going wrong is Lite-on erase, this is for Phat's.
Follow the tutorials, there are loads about.
All that needs to be done is:-
NEW PCB - Not flashed.
Switch to WP1, intro, Yes, Power cycle. Write firmware, lock SPI, outro x2, switch to WP0.
Already Flashed PCB.
Switch to WP1, intro, Yes, power cycle, unlock spi, write firmware, lock SPI, outro x2, switch to WP0.
(May be a few bits missing as I'm going by memorey and its 2am here so forgive any little listakes, but you get the idea)
I think I had a bad flash when i first flashed it. Could that explain the 0x80 and intro problems?
BL4K3Y
VIP Member
Read this - the unlocked PCB is to be treated as a phat Lite-On so Lite-On erase will work for you to get it into Vendor mode (status 0x72).
Ensure the switch is set to WP#=1 when doing this and once you have achieved status 0x72, write your firmware, click the SPI status button (it should show 0x00 and will change to 0x8C), set the switch to WP#=0 and send the Outro command.
If everything went well, you should now have a functioning PCB which you can place in your drive and enjoy your games
!
Last edited:
Ok, I have already said Ive done liteon erase and still get 0x80. I checked phat and it fails to intro the drive....
BL4K3Y
VIP Member
Is JungleFlasher using "Additional Functions" to power cycle your drive?
BL4K3Y
VIP Member
If you installed the CK3i drivers, tick the "Additional Functions" box and try again.