Flashing green, no Xell

D

Djirko

Senior Member
Jan 6, 2012
125
0
Lithuania
www.playbox.lt
Hello,
its not my first xbox that im doing rgh. Basically its my third slim(trinity). I have a problem. I have read the nand, created ecc, then wrote it. Programmed coolrunner, installed it and did everything how im doing all the time. But when i powering on green light on cr always flashing and to glitch. Waited about 5mins, tried both phat and slim modes on cr.
I even desoldered CR power and wrote original nand back and xbox booted normally, so i didint do anything bad. I tried to resolder again, but same thing happens. Just flashing green ( as it should ) and doesnt glitch.
Here is my pics of soldering, but i couldnt get better quality with my phone, so sorry about that.
 
D

Djirko

Senior Member
Jan 6, 2012
125
0
Lithuania
www.playbox.lt
Djirko said:
Hello,
its not my first xbox that im doing rgh. Basically its my third slim(trinity). I have a problem. I have read the nand, created ecc, then wrote it. Programmed coolrunner, installed it and did everything how im doing all the time. But when i powering on green light on cr always flashing and to glitch. Waited about 5mins, tried both phat and slim modes on cr.
I even desoldered CR power and wrote original nand back and xbox booted normally, so i didint do anything bad. I tried to resolder again, but same thing happens. Just flashing green ( as it should ) and doesnt glitch.
Here is my pics of soldering, but i couldnt get better quality with my phone, so sorry about that.
Click to expand...
I know that some of the wires are exposed too much, but its because i resoldered it second time so some them melted a little, but im 100% sure they dont touch the board.
 
D

Djirko

Senior Member
Jan 6, 2012
125
0
Lithuania
www.playbox.lt
dgenx said:
try and move it up towards the xclamp a bit and not have it so tight in a loop.

i say thats your prob tbh.
Click to expand...
Something like that? I uploaded to imaheshack, because somewhy i cant to add more attachements.
http://img707.imageshack.us/img707/5065/img20120204014941.jpg
Well anyway i tried different positioning and etc and it still doesnt glitch. Im starting to think, to try different CR and resolder ecerything from scratch.
 
Martin C

Martin C

VIP Member
Jan 10, 2004
35,981
0
Scotland, UK
www.team-xecuter.com
Your soldering looks ok (you won't hear me say that a lot).

What did you use to build the ECC? Any bad blocks in your NAND?
 
  • Like
Reactions: Djirko
D

Djirko

Senior Member
Jan 6, 2012
125
0
Lithuania
www.playbox.lt
socalbill said:
try running your wires like this...40+ Slim RGHs now and not one failure to boot...you don't have to use tape, but I absolutely hate hot glue.

http://i1083.photobucket.com/albums/j398/socalbilljtag/IMG_0278.jpg
http://i1083.photobucket.com/albums/j398/socalbilljtag/IMG_0279.jpg
http://i1083.photobucket.com/albums/j398/socalbilljtag/IMG_0280.jpg
Click to expand...
Its sick man :D I moved the blue wire under xclamp as shown in your pics and it booted o_O

---------- Post added at 17:20 ---------- Previous post was at 17:14 ----------

so, wire positioning have so much influence for booting?
 
D

Djirko

Senior Member
Jan 6, 2012
125
0
Lithuania
www.playbox.lt
Hmm,
but what can i do to make these boots more stable? Because some time its boots almost instant, some times it doesnt boot at all or takes 30-60sec.

---------- Post added at 17:30 ---------- Previous post was at 17:26 ----------
Djirko said:
Hmm,
but what can i do to make these boots more stable? Because some time its boots almost instant, some times it doesnt boot at all or takes 30-60sec.
Click to expand...
Its like console is booting either instant or like 1-2mins. Should i try shorten the wire or search for other positions?
 
x360ccm

x360ccm

BANNED
Jan 18, 2011
3,616
0
south coast UK
thats slims for you.tbh. you could try the switch on phat.

trim the wire.

coil the wire and not have it like them pics.

all slims are diff .

longest one boots for me is 30 seconds.

but i one of them once it booted then you play.

i do use qsb on slims tho to.
 
Last edited:
  • Like
Reactions: Djirko
D

Djirko

Senior Member
Jan 6, 2012
125
0
Lithuania
www.playbox.lt
Thank you everyone who helped. I got some good knowledge from you guys. I managed that slim to boot in 10sec almost every time. So i will share how i did that ( in case anyone would need that info ). Wire lenght 47cm, position - under xclamp ( as in pictures before, only in coil ), mode - phat ( slim was unstable, it booted instanly or in 1-2mins ). Anyway mods can change this topic as fixed. Again thank you guys.
 
You must log in or register to reply here.