when i turn on my xbox it will freeze on the xbox logo rox my box........ i dont know what the promblem is....... i try to use back the backup pressing eject/pwr but the screen you see flickers....... i can see a little of the tittle flashbios 301 but it is impossible to read whats it says..... if anyone knows whats wrong with my chip please let me know........ i hope its still fixable........thanks
freeze!!!! dont know what happened....
- Thread starter dekciwgeo
- Start date
i loaded 2914 bios everything was working fine........ i was trying to load my evox dashboards but i keep on resetting the xbox to read the disc..... and now its like this....
verson 1.2/1.3 x3 chip
bio 2914
i think before i turn off the xbox i was looking in the eep something and it as me to reset something but i press the wrong botton so it reset.....i dont know if that has to do with anything.......
to me i think i must have screwed up the bio.... is there any way to reset the chip...
verson 1.2/1.3 x3 chip
bio 2914
i think before i turn off the xbox i was looking in the eep something and it as me to reset something but i press the wrong botton so it reset.....i dont know if that has to do with anything.......
to me i think i must have screwed up the bio.... is there any way to reset the chip...
I think your solder is fine. I do think you may have screwed up your X3 eeprom though. There is a way to reset it. I recall you have to dl Evox bios and flash it to one of the banks. Then dl X3 eeprom erase and ftp it into your xbox then run the file. You have to search for it since I'm sort of busy but if I have time later, I'll search for the direct link to the steps to do it for you. Sorry.
come to think about it, could you have chaged the video option? Double check on your cable first. If cable is ok but still have problem, try this guide that someone else posted. If still no go, them reset your x3 eeprom as last resort. I'll look for that thread tonight for you. Thread: http://www.teamxecuter.com/forums/showpost.php?p=97847&postcount=2
Whole thread: http://www.teamxecuter.com/forums/showthread.php?t=26789&highlight=eeprom
Whole thread: http://www.teamxecuter.com/forums/showthread.php?t=26789&highlight=eeprom
Last edited:
dijkhuizenh
Noob Account
- Mar 2, 2005
- 4
- 0
almost a simular problem here. I have installed the Xecuter 3 CE chip on my xbox v1.5 after that i flashed the bios version x3 3029 via http. Then i turned on my xbox and it wont go further then the xbox xecuter rox my box logo.
I tried some other bios versions but it still hangs on the rox my box logo.
I also checked al the solder points iam almost 100 % sure that they are ok.
i hope you guys have some idea`s to help me out.
I tried some other bios versions but it still hangs on the rox my box logo.
I also checked al the solder points iam almost 100 % sure that they are ok.
i hope you guys have some idea`s to help me out.
help
i finished the install today and all was working fine. i went to flash from the hd, and clicked the first. the bar went green and the xbox turned off like it was supposed to. now when i turn it on, it starts than turns right back off. if i hit a button just right the box stays on, but there is no image on screen...what do i do?
i finished the install today and all was working fine. i went to flash from the hd, and clicked the first. the bar went green and the xbox turned off like it was supposed to. now when i turn it on, it starts than turns right back off. if i hit a button just right the box stays on, but there is no image on screen...what do i do?
make sure to flash with the correct bios for your xbox version. You can attempt to reflash again. Set your switches to on on off off off (I assume you set this already), press power and eject buttons at the same time until your x3 cp turns purple. That should get you to backup flashbios and you can reflash from there.deharvey said:i finished the install today and all was working fine. i went to flash from the hd, and clicked the first. the bar went green and the xbox turned off like it was supposed to. now when i turn it on, it starts than turns right back off. if i hit a button just right the box stays on, but there is no image on screen...what do i do?