freezing during Gameplay CR4, RJTAG Jasper 256 BB

h1n1viruz · Feb 28, 2015

Console Type: Jasper
Programmer Used: JR v2
NAND Size: 256
Dashboard version: 17150
CB Version: 6754
Screenshot of NAND details from J-Runner: Jrunner pic below
J-Runner log
updflash.bin log (if applicable)
Image of the CR4 XL, and the MOBO will come tomorrow.
Was the console working before you started: Yes. 100% fine
Do you get a green debug light appear on the CR4 XL chip 4-5sec? well no. it boots after first
How long is the light on for each time : glitches as soon as i power on, sometimes will have to glitch twice to boot, but very rare.

Problem.
I got this jasper BB working good and after testing and even slight playing it stays on with no freezing,
Then i go to boot a GoD and it freezes when i try to load a level.
Try it again and works fine.
back to dashboard, and load a arcade game... freezes at menu screen.
Xell will boot no issues, i did have to wire my CPU_RST wire Alone through one hole and the rest through another.
Soldering is good and good points, even retouched several points on the board to make it look fresh and not cold joints.
The placement of the Cr4 xl is under the DVD by the Hdd connector.
I do have 12v mod on the jasper (only cause im paranoid)
AND had 0 bad blocks on the nand and im not gonna use that white cpu_rst wire it has been bad to me. lol :crazy:

but how would i go about placement of the CPU_RST wire?
as stated ill post pics of the MOBO and the CR4 xl tomorrow.

February 19, 2015 8:56:40 PM

J-Runner v0.3 Beta (7) Started

WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button

Checking Files
Finished Checking Files
Version: 10
Flash Config: 0x008A3020
008A3020
Jasper 256MB
CB Version: 6754
Jasper 256MB Manually Selected
Reading Nand to \\psf\Home\Downloads\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 13:54 min:sec

Reading Nand to \\psf\Home\Downloads\J-Runner v3 (5) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Jasper 256MB
Jtag Selected
Nand Initialization Finished
Reading Nand
Done!
in 13:54 min:sec

Comparing...Takes a while on big nands
Nands are the same
Aud_Clamp Selected
R-Jtag Selected
Patching Jasper version 2.3 SMC at offset 0x12BA
XeLL file created Successfully jasper_hack_bigblock_aud_clamp.bin
Version: 10
Flash Config: 0x008A3020
Writing Nand
jasper_hack_bigblock_aud_clamp.bin
Done!
in 0:17 min:sec

Unable to find the specified file.

===================================================
February 20, 2015 8:35:42 PM

J-Runner v0.3 Beta (7) Started

WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button

Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Jasper BB
Jtag Selected
Nand Initialization Finished
Initializing nanddump1.bin..
CpuKey is Correct
Added Key to Database
Jasper BB
Nand Initialization Finished
Moving All files from output folder to \\psf\Home\Downloads\J-Runner v3 (5) Core Pack\120068484705
Initializing nanddump1.bin..
Jasper BB
Nand Initialization Finished
Aud_Clamp Selected
R-Jtag Selected
Initializing nanddump1.bin..
Jasper BB
Nand Initialization Finished
R-Jtag de-Selected
Aud_Clamp de-Selected

===================================================
February 20, 2015 8:44:57 PM

J-Runner v0.3 Beta (7) Started

Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Jasper BB
Jtag Selected
Nand Initialization Finished
Aud_Clamp Selected
R-Jtag Selected
Load Files Initiliazation Finished
Clean SMC detected
Patching Jasper version 2.3 SMC at offset 0x12BA
17150
Started Creation of the 17150 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.14.693
---------------------------------------------------------------
base path changed to \\psf\Home\Desktop\Modding Everyday CR4 Tutorial\J-Runner v3 (5) Core Pack\xeBuild
---- { Image Build Mode } ----
building jtag image

**************** WARNING *************************
nanddump.bin has NAND memory unit data, make
sure you back up any important data off the
internal MU before flashing a new image!
****************************************************

******* WARNING: could not patch SMC reset limit!

---------------------------------------------------------------
\\psf\Home\Downloads\J-Runner v3 (5) Core Pack\120068484705\updflash.bin image built, info:
---------------------------------------------------------------
Kernel : 2.0.17150.0
Console : Jasper (big block)
NAND size : 64MiB (system only)
Build : JTAG
Xell : power on console with console eject button
Serial :
ConsoleId :
MoboSerial:
Mfg Date : 11/21/2008
CPU Key :
1BL Key :
DVD Key :
CF LDV : 18
KV type : type2 (hashed - unchecked, master key not available)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to \\psf\Home\Downloads\J-Runner v3 (5) Core Pack\120068484705
Image is Ready
Initializing updflash.bin..
Jasper BB
Nand Initialization Finished
Initializing updflash.bin..
Jasper BB
Nand Initialization Finished
Initializing updflash.bin..
Jasper BB
Nand Initialization Finished
Jasper 256MB Manually Selected
Version: 10
Flash Config: 0x008A3020
Writing Nand
updflash.bin
Done!
in 14:23 min:sec

gavin_darkglide · Feb 28, 2015

Google falcon rgh freeze, and I am sure you will find a solution. There are tons of guides on this.

joshypoo · Feb 28, 2015

Yes i agree. some research would help. But since i am a nice guy

Try to change SMC power settings in J runner

Here
http://www.se7ensins.com/forums/thr...diting-fixes-falcon-freezing-on-rgh2.1166312/

joshypoo · Feb 28, 2015

I also noticed that you have a 12v fan mod on your jasper. this is not necessary since it is a Jasper.
if it runs hot without it then you need to re do the thermal compound on it.

h1n1viruz · Feb 28, 2015

I wasnt sure if the SMC change applied to the jasper, but ill give that a go. thanks for helping me in that direction.

i used the 12v fan mod only cause i am paranoid,
Stock - 50C
12v - 39C
thought it wouldnt affect anything since i got the power source from the bottom of the board where the power connector is at.
Well ill take it off and take a few shots of the board for you all.
This is my First ever 360 mod.
But thanks for the help. ill be back in a bit after.

joshypoo · Feb 28, 2015

instead of doing a 12v fan mod you can simply change the target temps in dashlaunch or change them in the SMC config in J runner.

gavin_darkglide · Feb 28, 2015

The 12v fan mod is bad, it can cause problems down the line with blown mosfets. You are much better off changing target temps in dashlaunch, or the smc.

h1n1viruz · Feb 28, 2015

Well update. i have now played it in games and been trying to duplicate the freezing. nothing so far.
I removed the 12v fan mod, cleaned the old thermal paste and reapply some on the cpu and gpu.
Move the CPU_RST wire more inward under the mobo.
uploading the pictures of my mobo... brb ;D
CR4 XL

Under the CPU

POST out

RJTAG QSB Green wire

RJTAG QSB

QSB Topside

Those are my QSB's and under the CPU they arent bridged or anything. its just the angle of the shot. i also have limited room to work. so its on the floor of my room. lol but i tried to solder the best i can. followed the tut from the youtube channel moddingeveryday

Search

Search

freezing during Gameplay CR4, RJTAG Jasper 256 BB

h1n1viruz

Junior Member

Attachments

gavin_darkglide

joshypoo

joshypoo

h1n1viruz

Junior Member

joshypoo

gavin_darkglide

h1n1viruz

Junior Member