FSD boots, but Xell does not. Tried reflashing NAND. Still same problem

[Kexxen]

So I have a Corona V2 that I RGH'd successfully. It boots freestyle dash and everything fine, but rarely boots Xell (most often Xell flickers, but then the screen goes blank). Occasionally, Xell will boot, display CPU key etc. But then if I try to run something from a usb stick, Xell says "executing" and the screen goes blank (this has happened with two different programs that I tried). I tried reflashing my NAND with an Xebuild image that I made today from my original nanddump.bin, but still have the exact same problem. Does anyone have any suggestions?

Thanks in advance!

 

[BL4K3Y]

Which version of XeLL Reloaded is on the console?

Browse to J-Runner's "common\xell" directory and delete "xell-gggggg.bin".

Restart J-Runner, let it download the missing file and build a new NAND image.

I am not saying that this will fix your issue, but it is possible that the XeLL image was corrupted somehow.

 

[Kexxen]

Which version of XeLL Reloaded is on the console?

Browse to J-Runner's "common\xell" directory and delete "xell-gggggg.bin".

Restart J-Runner, let it download the missing file and build a new NAND image.

I am not saying that this will fix your issue, but it is possible that the XeLL image was corrupted somehow.

It says v0.993. I'll give that a try and see if it works. Thanks for the quick reply.

 

[Kexxen]

Which version of XeLL Reloaded is on the console?

Browse to J-Runner's "common\xell" directory and delete "xell-gggggg.bin".

Restart J-Runner, let it download the missing file and build a new NAND image.

I am not saying that this will fix your issue, but it is possible that the XeLL image was corrupted somehow.

I tried these steps. It didn't seem to fix it (I know you didn't guarantee it would). But I appreciate the response.

Now, I don't know if this is of significance, but immediately after writing the ecc file, Xell had no problem booting.

 

[BL4K3Y]

Now, I don't know if this is of significance, but immediately after writing the ecc file, Xell had no problem booting.

Are you saying that the console boots to XeLL with video every time with only the ECC image written?

 

[Kexxen]

Are you saying that the console boots to XeLL with video every time with only the ECC image written?

Yes, that is what I mean.

 

[Kexxen]

Are you saying that the console boots to XeLL with video every time with only the ECC image written?

:crazy:

 

[Kexxen]

Sorry for my confusion, but yes. I just tested again by writing ECC. With only the ECC written, Xell booted 10 times in a row. After I created Xebuild and wrote NAND, it didn't boot Xell with video once after 5 tries.

 

[Krafter]

Try building a 16767 image and try that.

 

[Kexxen]

Try building a 16767 image and try that.

I appreciate your input. However, I gave 16767 a try and I still have the same problem.

 

[Krafter]

Try building an image using AutoGG.

 

[Kexxen]

Try building an image using AutoGG.

On the web page for AutoGG, it says that it's for Glitch 2m. I've been using Glitch 2. Should I switch to 2m or does it matter?

 

[Krafter]

Couldn't hurt to try.

 

[Kexxen]

Try building an image using AutoGG.

I can't quite figure out how to use AutoGG. When I go to create the Xebuild, it says I need to download the dash. When I try to download the dash, it just says "Data error aborting". Anyway, I'll do some research and get back on the forum tomorrow. Thanks for your help!