Hi, after successfully jtagging my xbox, I installed latest dash 16537 and every time i press the guide button to access the mini menu/mini blades the menu will come up blank and freeze the system.
This even happens if I try to install the avatar update from USB, the notification will come up blank and then freeze.
However other notifications will not freeze the xbox i.e. can't connect to xbox live error works fine.
I get Error: 250 reading block 1F5 when I dump the nand but JRunner seems to remap it. Xell still brings up the bad block error 0x00..0204 or something about 0x1f5 when I flash the nand.
Not sure if this is the cause of the problem.
I used a temporary work around by installing dash 14717 which functions perfectly apart from FSD3 LiNK not showing up in the mini menu/mini blades, which I'd really like to get running. I did some searching and tried to update to the latest dash again to try and get LiNK running, if that was the cause for LiNK not showing up in the first place but the mini menu freeze is preventing progress.
Am I missing something obvious here? Or could it be something else like the soldering joints or nand. I've tried builds from JRunner and xeBuild to the same result.
Would appreciate any help on this issue.
I'm on a Xenon MB, here is a thread about the install
http://team-xecuter.com/forums/showthread.php?t=142313&p=978828#post978828
I also get Error: 202 writing and erasing block 1F5
Log for the bad blocks
Update:
Managed to get the mini menu working.
Fflashed a retail nand and then did an erase, checked include dashlaunch on a new xeBuild image and flashed nand directly from JRunner.
LiNK still isn't working but thats a separate issue
Thanks anyway!
This even happens if I try to install the avatar update from USB, the notification will come up blank and then freeze.
However other notifications will not freeze the xbox i.e. can't connect to xbox live error works fine.
I get Error: 250 reading block 1F5 when I dump the nand but JRunner seems to remap it. Xell still brings up the bad block error 0x00..0204 or something about 0x1f5 when I flash the nand.
Not sure if this is the cause of the problem.
I used a temporary work around by installing dash 14717 which functions perfectly apart from FSD3 LiNK not showing up in the mini menu/mini blades, which I'd really like to get running. I did some searching and tried to update to the latest dash again to try and get LiNK running, if that was the cause for LiNK not showing up in the first place but the mini menu freeze is preventing progress.
Am I missing something obvious here? Or could it be something else like the soldering joints or nand. I've tried builds from JRunner and xeBuild to the same result.
Would appreciate any help on this issue.
I'm on a Xenon MB, here is a thread about the install
http://team-xecuter.com/forums/showthread.php?t=142313&p=978828#post978828
I also get Error: 202 writing and erasing block 1F5
Log for the bad blocks
Code:
Comparing...
Bad Block ID 01F5 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 01F5 [Offset: 0x812A00]
Bad Blocks Remapped
Bad Block ID 01F5 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 01F5 [Offset: 0x812A00]
Bad Blocks Remapped
Nands are the sameManaged to get the mini menu working.
Fflashed a retail nand and then did an erase, checked include dashlaunch on a new xeBuild image and flashed nand directly from JRunner.
LiNK still isn't working but thats a separate issue
Thanks anyway!
Last edited: