hello every body I bought the Rjtag ....the package without qsb v3 ..... where to connect the orange cabel named K on xbox please ????
FIXED hello . i don't have QSB ...where can i connect K
- Thread starter rinaadel
- Start date
BL4K3Y
VIP Member
BL4K3Y
VIP Member
Console Type: jasper
NAND size: 16
Dashboard version: e.g 2.0.15574
CB version: e.g 5774
Screenshot of NAND details from J-Runner:
Image of R-JTAG board:
Images of close-up soldering to motherboard:
NAND size: 16
Dashboard version: e.g 2.0.15574
CB version: e.g 5774
Screenshot of NAND details from J-Runner:
Image of R-JTAG board:
Images of close-up soldering to motherboard:
Dark_Riku
VIP Member
- Mar 2, 2012
- 356
- 0
What error is the console throwing at you? If it's 0010 then it's completely normal and you just have to mess around with whatever settings works for your console. There are plenty of threads available to see and try what works best for you.
Maybe clean up the soldering a bit and check each point. It doesn't look really "clean to me".
Maybe clean up the soldering a bit and check each point. It doesn't look really "clean to me".
It glitches and giving greed leds inintervals as usual but give 3 rrod after about 20 seconds .
What trials i have to try please and in which piece ?
What trials i have to try please and in which piece ?
Dark_Riku
VIP Member
- Mar 2, 2012
- 356
- 0
It may be the angle of the POST_QSB, but give some extra dabs on them to make sure they are 100% connecting. If it's glitching then it should be fine. However doesn't hurt to make it clean.
As for the wiring on top of the board and the chip, Probably best to clean that up a little bit..trim the wire a bit too if necessary.
Figure out what error code you're getting.
Turn on the console until it gets RRoD, then hold the Sync Button and press Eject 4 times (Each time displays a number that is relevant to your error code)
e.g If I had my console laying horizontal (Flat) and I done the code test.
I hold the Sync button and press Eject one time, let's say I get all 4 lights flashing. This will indicate the number 0
Then I do the same as above and get the exact same code, this would be another 0
Now, repeat again and I get 1 flashing light on the top left, this will be number 1
finally repeat again what we did the other three times and I am presented with 4 flashing lights again. So my next number will be 0.
Now you have your error code. 0010 - If it is indeed the exact same here, then it's just a case of messing with the dip settings and possibly the voltage settings to see what likes your console best.
If I have confused you with the whole error code thing, here's a video tutorial on how to do it - [video=youtube;REsIJQqbmos]http://www.youtube.com/watch?v=REsIJQqbmos[/video]
I have resolved the problem by putting the switch 3,7,8 ON everything is ok and it boots within 10 seconds max .....thanks Team xecuter 
Antalpromille
VIP Member
i dont get it, why does so many people ask for support before reading and following the tutorials/manuals?I have resolved the problem by putting the switch 3,7,8 ON everything is ok and it boots within 10 seconds max .....thanks Team xecuter
Dark_Riku
VIP Member
- Mar 2, 2012
- 356
- 0
Good to see you have it working nowI have resolved the problem by putting the switch 3,7,8 ON everything is ok and it boots within 10 seconds max .....thanks Team xecuter
Ubergeek
Xecuter Groupie
Reading the instructions is awesomeI have resolved the problem by putting the switch 3,7,8 ON everything is ok and it boots within 10 seconds max .....thanks Team xecuter
if you have had read all the instructions and info , you may have been able to sort it yourself :wink:I have resolved the problem by putting the switch 3,7,8 ON everything is ok and it boots within 10 seconds max .....thanks Team xecuter