HELP! CORONA V1 NOT BOOTING PROPERLY!

willstrz

willstrz

Full Member
Aug 13, 2015
89
0
Florida
Hello all. I have a emergency with my Corona v1. And the story goes... I had pre-soldered the points to where they have to go (my CR4 and JR-Programmer havent arrived yet :p), and everything turned out fine. no bad things hopefully have not happend yet. so, i went up to take a shower and left the board with power. i came back down to a red light that stayed on for about 30 seconds, then went off. EVERYTHING shut off. i heard the hard drive click off. (i did not have the DVD drive plugged in because on the cable that goes to the drive, there is a pink and blue side. wasnt sure if the pink went on the left or right, so i left it unplugged.) so, after that i immediately unplugged it, and it shut off. then i unplugged everything from the board, and put the hdd and the wifi card back in place. this time, i had the hdd, the wifi card and the hdmi plugged in. i plugged the psu in, and it booted with all four of the lights go into the array they would retail. i got the xbox360 intro, then it shut off and the light turned red...? wtf happend? also, when i have the dvd drive plugged in, all i get is the start sound when i press the on button. PLEASE, help me!


------UPDATE-----

now when i plug the hdd, wifi and unplug the fan, plugin the HDMI, i get no lights, or anything on my monitor. it just makes the sounds.
 
Last edited:
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
willstrz said:
Hello all. I have a emergency with my Corona v1. And the story goes... I had pre-soldered the points to where they have to go (my CR4 and JR-Programmer havent arrived yet :p), and everything turned out fine. no bad things hopefully have not happend yet. so, i went up to take a shower and left the board with power. i came back down to a red light that stayed on for about 30 seconds, then went off. EVERYTHING shut off. i heard the hard drive click off. (i did not have the DVD drive plugged in because on the cable that goes to the drive, there is a pink and blue side. wasnt sure if the pink went on the left or right, so i left it unplugged.) so, after that i immediately unplugged it, and it shut off. then i unplugged everything from the board, and put the hdd and the wifi card back in place. this time, i had the hdd, the wifi card and the hdmi plugged in. i plugged the psu in, and it booted with all four of the lights go into the array they would retail. i got the xbox360 intro, then it shut off and the light turned red...? wtf happend? also, when i have the dvd drive plugged in, all i get is the start sound when i press the on button. PLEASE, help me!
Click to expand...
Give us the secondary error, there are guides on how to do so.
 
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
willstrz

willstrz

Full Member
Aug 13, 2015
89
0
Florida
UPDATE: ok, plugged EVERYTHING in (except the HDMI) but i did plug in the DVD drive, HDD, wificard and i get a green led on the PSU and the RF Module board. but, i still dont get the array of green lights when i hit the on button. after about 30 seconds, it turns red and everything spins down...?
 
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
willstrz said:
UPDATE: ok, plugged EVERYTHING in (except the HDMI) but i did plug in the DVD drive, HDD, wificard and i get a green led on the PSU and the RF Module board. but, i still dont get the array of green lights when i hit the on button. after about 30 seconds, it turns red and everything spins down...?
Click to expand...
Push sync button and then Push four times eject, tell me which lights are on at every time you push eject
 
willstrz

willstrz

Full Member
Aug 13, 2015
89
0
Florida
its wired because when i plug it into one outlet no lights come on, but with the other outlet, the will lights come on.
 
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
willstrz said:
its wired because when i plug it into one outlet no lights come on, but with the other outlet, the will lights come on.
Click to expand...
Oh, my bad, you have to push and mantain sync, and them to push four times eject, with sync pushed all the time
 
willstrz

willstrz

Full Member
Aug 13, 2015
89
0
Florida
um well something happend. it booted. i played a little James Bond Golden Eye (a classic lol) then it just shut off and the PSU turned red. I tried plugging it back in, pressing the on button, the green light came on for a split second, then turned off and the PSU turned red. i will try what you said for me to do - "Oh, my bad, you have to push and mantain sync, and them to push four times eject, with sync pushed all the time"
 
Nintendo

Nintendo

VIP Member
Sep 5, 2014
605
33
Spain
willstrz

willstrz

Full Member
Aug 13, 2015
89
0
Florida
i do dearly apologize for the lack of responce, but here is the soldering job: https://vid.me/Y0mg nothing is bridged that i can see. i removed the dvd drive, hdd, and hdmi and i just had the wifi card in and nothing happend. it didnt turn red, it just made the turn on sound and did nothing at all. also, i need a quicker way to talk to you lol.
 
willstrz

willstrz

Full Member
Aug 13, 2015
89
0
Florida
ok. if you return, when i turn the xbox on, then i hear a sharp click noise then it turns off. not sure where it is located though...
 
You must log in or register to reply here.