ANSWERED Help cpu bypass!

[cj_goalie31]

Hi i have a falcon board that was running fine and had FSD installed. I went to go play it and then it wasn't working i took it apart and found that the green wire had ripped off and the pad just above it towards the x-clamp had fallen off also. I was just wondering if there is any way to fix this when i flash stock nand back it boots fine. I have a broken falcon board also. I was wondering if i took the piece from that and soldered it on would it work?

thanks for any help,

 

[cj_goalie31]

picture

 

[J2G]

You need to post a clear picture the one posted is too blurry also i'd say your going to have a look here by the sounds of it buddy >>> Alternate RGH Points - How To Fix When You [email protected]*k up . By Uber

 

[cj_goalie31]

kk so i did the alternate points but were does the green wire go?

 

[Noob.Si.BOT]

You got too much bridges i see, i had the same issue i melted the solder on the board and cleaned it out that way. Once you connect to the cpu bypass get hot glue to keep it in place! thats what i did

 

[cj_goalie31]

not really my pad broke of like to metal part on top so it doesnt work and on the alternate point were does the green wire go

 

[cskalash]

The green wire goes anywhere you want between the resistor pad and the other side of the board alternate point.
resistor pad---------------------------other side of the board alternate

You can solder 2 wires to the resistor pad, one goes to the other side of the board to complete that track, and the other is your green wire.

 

[rexdale]

i found it easier to attach one wire to the resister, another wire to the alternate point, and then attach the free end of both wires to your coolrunner or whatever ur using

 

[cj_goalie31]

kk guys thanks for your help but i think that the board is fried i tried everything thing and i think that the xbox just simply won't work without that pad. so thanks for your help but im giving up.

 

[x360ccm]

where are you,maybe send it to somebody who would sort it.for you.

 

[J2G]

kk guys thanks for your help but i think that the board is fried i tried everything thing and i think that the xbox just simply won't work without that pad. so thanks for your help but im giving up.

You where asked to post a better picture then then one you posted so people can see it the one you posted is to blurry but looks like bridging ..

 

[knowlzy10]

got to agree with johnny, that pic is pants if i zoom in it just looks like a big blob of solder, if you want better answers/help post clearer pics

 

[x360ccm]

i did one of these today.i post a pic of how i did it.in the mornin

i think the diff will be that on the one i did.the pad and resistor had been took off.

 

[x360ccm]

this is one that i got and had the resistor and pad gone.this is how i did it.

well i got to put the wire straight and heat shink over it but you get the idea.

 

[cj_goalie31]

kk from you pic i started to get some hope thankyou very much just wondering could it be possible for you to post a pic from the other side of the board please and what resistor did you use.

thanks,

 

[x360ccm]

i not takein the heat sink of again

but look at the bolt you got a green wire ok.that gose to the alt point

the resistor i use is 10k.

the green wire that is straight on the resistor is the green one that comes from the coolrunner.which is the one you get in the phat pack.:rolleyes2:

yes this was one fcuk mobo it came dead bolts included.but now runs.fine.

well i just got to finish of the heat wrap tidy up wires .

 

[cj_goalie31]

kk ill try thank out as soon as i get a 10k resistor i was just wondering does it have to be a 10k resistor or would others work?

 

[x360ccm]

you in the uk i send you 1 gee yes it a 10k.

 

[cj_goalie31]

and this is my board im not sure if its good enough quality but with thos pads off do you think it will work?

 

[cj_goalie31]

sorry im not in the uk i think i have one it's 1/4 watt 10k ohms which should work