LITEON DG-16D4S - SLIM help liteon 0225 brick

[roger_tik]

hello,

first of all, sorry for my english.

i was trying to flash a drive 0225 with winbow chip. i read the key, without no problem.

then i pass for the kamikase unlock. i start drilling, jf made a beep and the spi was clear. when i tried to make a dump, my laptop freese and i guess know i have the drive brick.

i an using xbox360 pro.

can someone help me unbrick the drive

 

[Suicyde]

You should still be fine to re-intro the drive, and get it back into vendor mode...then proceed with full dump & flash with LT+ v1.92.

 

[roger_tik]

when i try intro it take a long time until it get 0x72 status, and the chip properties aren t correct. then i try to wri and gat the massage, unknown chip.

don t let me writ on it

 

[diaboliq20]

have u tried an outro/ATA reset on it then tried vendor mode again?

 

[roger_tik]

i get this massage when i do intro.

 

[diaboliq20]

send lock SPI command to it....outro, and then start again...NO DRILLING just use some rubbing alcohol on the hole

 

[sp4rkst4rt3r]

You need to post your JF log buddy

 

[roger_tik]

then i it ok, and get this other massage, and don´t let me write on it

 

[roger_tik]

send lock SPI command to it....outro, and then start again...NO DRILLING just use some rubbing alcohol on the hole

how can i do that?

it look likes spi is unlock

 

[diaboliq20]

try hitting CTRL SHIFT F11

 

[roger_tik]

try hitting CTRL SHIFT F11

when i did that jf said drive is still lock

what can i do?

 

[diaboliq20]

now try re-unlocking it
start over, and use either your finger or some rubbing alcohol on the chip to unlock

 

[roger_tik]

now try re-unlocking it
start over, and use either your finger or some rubbing alcohol on the chip to unlock

but how can i do that?
where in jf?

when i press intro jf don´t send the unlock comand

 

[diaboliq20]

I see your radio button is on slim....for the unllock it should be on phat I think

 

[roger_tik]

I see your radio button is on slim....for the unllock it should be on phat I think

change it for fat and get the same result.
received a massage of returm the MRA hack back to normal.

it look likes it´s not entering into vender mode properlly.

 

[sp4rkst4rt3r]

You need to post your JF log buddy

Do that ^^^^^^

 

[roger_tik]

Do that ^^^^^^

how can i do that?
i put some prints of jf on post before. isn´t that it?

 

[roger_tik]

can someone help please

 

[x360ccm]

open your jf log copy and paste it,and post it here

 

[roger_tik]

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
JungleFlasher 0.1.87 Beta (277)
Session Started Fri Sep 23 17:43:22 2011
This is a Wow 64 process running on 2 x 64 bit CPUs
X360USB PRO detected, Version 0.18
portio64.sys Driver Installed
portio64.sys Driver Started, thanks Schtrom !
Found 3 I/O Ports.
Found 1 Com Ports.
Found 5 windows drives C: D: E: F: Q:
Found 1 CD/DVD drives E:
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro:
..........................................................................
Serial flash found with Status 0x72
Sending Device ID request to port 0x0000
Spi Status: 0xFF
Manufacturer ID: 0xFF
Device ID: 0xFF
Flash Name: Unknown type
Flash Size: n/a