LITEON DG-16D2S holy crap, help

[dr.dookers]

flashing my liteon v7 from 1.9 to 2.0 with the blaster, had it in vendor mode trying to flash when my dog pushed in the tray! device intro failed, cant eject the tray no matter what i try, cant get back into vendor mode. please help, thanks

 

[xbox360 hacker]

do you have your key ?

 

[dr.dookers]

yes

 

[xbox360 hacker]

Try outra/ata if that doesn't work follow these steps:

1. start jungle flasher up
2. load your dummy.bin or ofw.bin as source
3. do you wish to auyo-load lite-on lt-plus select yes
4. check its lt-plus 2.0 that has auto loaded and keys match
5. NOW SELECT mtk flash 32 tab
6. lite-on erase then yes then you will need to power cycle
7. now you should have status 0x72
8. erase then write
9. outro/ATA reset
10. try your xbox360 out

 

[skiiermike]

flashing my liteon v7 from 1.9 to 2.0 with the blaster, had it in vendor mode trying to flash when my dog pushed in the tray! device intro failed, cant eject the tray no matter what i try, cant get back into vendor mode. please help, thanks

I'm just curious because i'm no expert, but why was your tray out during the flash if it's been flashed before?

I have the same liteon and because I have my key all I do to update is enter vendor, erase and flash.

I just thought I'd ask because i'm sure i'm missing something.

 

[dr.dookers]

i cant get into vendor mode, it wont let me eject the tray, no drive detected

 

[xbox360 hacker]

I'm just curious because i'm no expert, but why was your tray out during the flash if it's been flashed before?

I have the same liteon and because I have my key all I do to update is enter vendor, erase and flash.

I just thought I'd ask because i'm sure i'm missing something.

your right there is no need to half open your tray

 

[dr.dookers]

i thought it had to be in vendor mode to read the drive, even after its been flashed

 

[xbox360 hacker]

If you still cant get it into vendor mode try restarting your PC then follow those steps again

 

[dr.dookers]

i get
Drive returned Status 0x72
Manufacturer ID: 0x0
Device ID: 0x0
Flash Name: Unknown type
Flash Size: n/a

 

[xbox360 hacker]

now flash your drive like i said in those steps and all will be sorted

 

[dr.dookers]

now i get
Drive returned Status 0x72
Manufacturer ID: 0x0
Device ID: 0x0
Flash Name: Unknown type
Flash Size: n/a
Unknown flash type Erase aborted !
Unknown flash type Write aborted !
Unknown flash type Erase aborted !

 

[xbox360 hacker]

try using an earlier version of jungle flasher never came across that problem and instead of erase then write just try write

 

[dr.dookers]

ok now ive erased but it hangs up on the writing

Blank verified OK !
Getting Status from port 0x09E0
SPi flash found with Status 0x72
Sending Chip Erase to Port 0x09E0
Writing target buffer to flash
Writing Bank 0: .

 

[xbox360 hacker]

is it possible to use a different sata port ?

 

[dr.dookers]

there are 2 onboard ports, i could try that, do i have to shut down comp to switch?

 

[xbox360 hacker]

i would advise shutting down to be honest

 

[igulpem]

ok now ive erased but it hangs up on the writing

Blank verified OK !
Getting Status from port 0x09E0
SPi flash found with Status 0x72
Sending Chip Erase to Port 0x09E0
Writing target buffer to flash
Writing Bank 0: .

There was one version of Jungleflasher recently that threw up the write error to a bunch of users. I believe it was 0.1.85b. Is that what you are using? If so, use 0.1.86b, write again, and I'm pretty sure you'll be good to go.

 

[dr.dookers]

couldnt recognize drive in other port

 

[dr.dookers]

i can get the drive in vendor mode, just cant write