How can I get my CPU Key if I cant boot into Xell? Jasper 265mb R-Jtag

[BrianD]

Console: Jasper 256mb
Dash: 15574

I am completely lost. I followed a really good tutorial on how to install R-Jtag. I was really careful and read the directions twice so I would only have to solder once but I am unable to get Xell to boot. I have been pouring over all these post for this problem and there are so many different answers to the same question.

I have my dips set 1,7,8 on.
I have voltage bridged to 1.2v
I have my jumper on 470

I have a full dump nand (i dumped the nand 2 times and have been using those but I do have one full dump)
here is what was in my log file

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Saturday, August 24, 2013 6:35:39 PM


J-Runner v0.2 Beta (290) Started






Checking Files
Finished Checking Files
Jasper 256MB Manually Selected
Checking Console..
Version: 10
Flash Config: 0x008A3020
CB Version: 6754
Version: 10
Flash Config: 0x008A3020
CB Version: 6754
Jasper 256MB Manually Selected
Reading Nand to C:\Users\Brian\Desktop\Software\J-runner\J-Runner v02 Beta (288) Core Pack\output\nanddump1.bin
Reading Nand
Error: 250 reading block 4D0
Done!
in 13:25 min:sec


Reading Nand to C:\Users\Brian\Desktop\Software\J-runner\J-Runner v02 Beta (288) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Jasper BB
Reading Nand
Nand Initialization Finished
Error: 250 reading block 4D0
Done!
in 13:25 min:sec


Comparing...Takes a while on big nands
Bad Block ID @ 0x009A [Offset: 0x13DA000]
Bad Block ID @ 0x009A [Offset: 0x13DA000]
Nands are the same
Checking Console..
Version: 10
Flash Config: 0x008A3020
CB Version: 6754
Version: 10
Flash Config: 0x008A3020
CB Version: 6754
Jasper 256MB Manually Selected
Reading Nand to C:\Users\Brian\Desktop\Software\J-runner\J-Runner v02 Beta (288) Core Pack\output\nanddump1.bin
Cancelled
Version: 10
Flash Config: 0x008A3020
CB Version: 6754
Jasper 256MB Manually Selected
Reading Nand to C:\Users\Brian\Desktop\Software\J-runner\J-Runner v02 Beta (288) Core Pack\output\nanddump1.bin
Reading Nand
Error: 250 reading block 4D0
Error: 250 reading block 1438
Error: 210 reading block 1439
Error: 210 reading block 143A
Error: 210 reading block 143B
Error: 210 reading block 143C
Error: 210 reading block 143D
Error: 210 reading block 143E
Error: 210 reading block 143F
Error: 204 reading block 1B00
Error: 204 reading block 1B01
Error: 204 reading block 1B02
Error: 204 reading block 1B03
Error: 204 reading block 1B04
Error: 204 reading block 1B05
Error: 204 reading block 1B06
Error: 204 reading block 1B07
Done!
in 53:37 min:sec


Reading Nand to C:\Users\Brian\Desktop\Software\J-runner\J-Runner v02 Beta (288) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Jasper 256MB
Nand Initialization Finished
Cancelled


===================================================
Saturday, August 24, 2013 8:21:38 PM


J-Runner v0.2 Beta (290) Started




WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button






Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Jasper BB
Nand Initialization Finished
Comparing...Takes a while on big nands
Bad Block ID @ 0x009A [Offset: 0x13DA000]
Bad Block ID @ 0x009A [Offset: 0x13DA000]
Nands are the same
Jasper 256MB Manually Selected
Patching Jasper version 2.3 SMC at offset 0x12BA
XeLL file created Successfully jasper_hack_bigblock_aud_clamp.bin
Version: 10
Flash Config: 0x008A3020
Writing Nand
jasper_hack_bigblock_aud_clamp.bin
Done!
in 0:18 min:sec


Tip: Load the nand on source to have quicker results.
Scanning......
No Xbox Detected
Finished
Tip: Load the nand on source to have quicker results.
Scanning......
No Xbox Detected
Finished
Tip: Load the nand on source to have quicker results.
Scanning........
No Xbox Detected
Finished
Tip: Load the nand on source to have quicker results.
Scanning........
No Xbox Detected
Finished

=======================================================================

I just need to boot into Xell to get my CPU Key but I cant get it to work. What suggestions should I follow?

 

[jsinger47]

Where are your POST logs?

Where are your installation images?

 

[gavin_darkglide]

where are the install pictures....... also leave dips 7 & 8 on, and work your way through all 18 combination, 1-6, then 1.2V 1-6, then 1.8V 1-6...... eventually something should boot, assuming the soldering is correct. also the guide says start with dips 5-7-8 on.

 

[BrianD]

I am unable to post pics at the moment. I will try the different settings though. I'm just afraid that I would do something something that I wouldn't be able to recover from and didn't know what post to listen to. Thank you for your response.

- - - Updated - - -

I am unable to post pics at the moment. I will try the different settings though. I'm just afraid that I would do something something that I wouldn't be able to recover from and didn't know what post to listen to. Thank you for your response.

 

[Taijigamer2]

Try to upload images of install and POST logs. Try all dips 1-6 one at a time. One of them should boot xell. Just follow the official Rjtag installation guide, u can't go wrong. Good luck.

 

[gavin_darkglide]

These things were stated in the original install guide posted by ubergeek when this first came out..... If you dont understand the process, how do you expect to make it work? Then again there is only two ways to learn, and people usually take the hard way. I would also suggest re-reading the guide one more time to see what else you may have missed...... lol. At least you are trying. That does count for something, but if you cant make it work, there are plenty of people on here who can...... I would offer but i am on the other side of the country..... and there are people closer to you who have been involved in the scene longer then i have with much more experience, and a lot less patience for people who cant seem to follow the guides.

 

[keefer95]

i had a few problems like this the other day . un solder the 1.2v bridge, its best to try everything as stock before changing things.