RGH How to put back again the Retail Microsoft Image

[krist]

Hi guys, I have problems with my RGH Jasper... It freeze all the time..
How to put back again the Retail Microsoft Image?

 

[jptrucking]

Try 360 multibuilder
If u want to get retail image back u need to take coolruner off the board.
:frown:

 

[Demitrios]

Flash back your original nand image.

 

[krist]

But when I use 360 Multi Builder and I choose to create an Retail MS Image it gives me an error: hacked SMC found? you should use a clen smc for a retail image!

---------- Post added at 03:24 ---------- Previous post was at 03:23 ----------

Flash back your original nand image.

How can I do that?

 

[keil423]

Did you not save one of your original nand dumps?

 

[krist]

Did you not save one of your original nand dumps?

yes, I saved... But how I put back the nanddump.bin in my nand?

 

[keil423]

Do you have Jtag tool V4.25 by chance?

If so just open Jtag tool.
Switch to advanced mode
Top left click main and select your device type and console type.
Now click reset glitch
Press write.bin and select you retail unmodded nand

it writes it and now your nand is stock. Leave offline and swtich coolrunner to Program to boot and test if nand is good.

 

[krist]

I used Nandpro3... I already create an retail_image.bin. How I put back in my nand?
Using NandX or USB disk?

 

[keil423]

Do you have Jtag tool V4.25 by chance?

If so just open Jtag tool.
Switch to advanced mode
Top left click main and select your device type and console type.
Now click reset glitch
Press write.bin and select you retail unmodded nand

it writes it and now your nand is stock. Leave offline and swtich coolrunner to Program to boot and test if nand is good.

 

[krist]

I got it... Thanks

---------- Post added at 03:52 ---------- Previous post was at 03:51 ----------

But the Xbox don't boot

 

[keil423]

Yeah just noticed your on a Jasper. What size nand you got?

Did you switch the coolrunner to Program when you tested it?

 

[krist]

16 mb, yes I switch the coolrunner to Program

---------- Post added at 04:04 ---------- Previous post was at 04:00 ----------

I need to take off the wires of the coolrunner?

 

[keil423]

16mb good! then that method should have worked for you. Have you tried desoldering the power wire from the coolrunner?

---------- Post added at 22:05 ---------- Previous post was at 22:04 ----------

Nand Pro command is NandPro Device: -w16 Nand.bin

replace device with either LPT or USB

just to answere your original question

 

[krist]

It is necessary to connect the dvd drive?

 

[keil423]

no. It should still boot without the dvd drive. You power light will just flash at you without it. There has been an ongoing battle around here with the Jaspers and not wanting to return to stock. Might search it once and see what you can dig up. I havent paid much attention to those post as I have never had a problem!

 

[krist]

I will trie desoldering the power wire from the coolrunner

---------- Post added at 04:14 ---------- Previous post was at 04:11 ----------

ok.. I will search for it... Thanks

 

[mafia 5k]

take any of your orignal dumps and simply write it back as you would any other image

nandpro30\nandpro.exe usb: -w16 (?original nand.bin?)

or use -w64 if you have big block nand if its not booting either you wrote the wrong image or your may have a problem with a point that you soldered too

 

[krist]

take any of your orignal dumps and simply write it back as you would any other image

nandpro30\nandpro.exe usb: -w16 (?original nand.bin?)

or use -w64 if you have big block nand if its not booting either you wrote the wrong image or your may have a problem with a point that you soldered too

I already write one of my original dump, but the xbox don't boot...
Now I just flash again the glitch image and in this moment I'm on dashboard, but if I put a game the console freeze...

---------- Post added at 04:48 ---------- Previous post was at 04:45 ----------

Even in the menus of dash sometimes it gives me an error...

 

[Martin C]

What have you done with the console since the original dump? Did you update it before starting the Coolrunner stuff or have you updated it since?

BTW, freezing is caused by the cable positioning.

 

[afsilver]

I used Nandpro3... I already create an retail_image.bin. How I put back in my nand?
Using NandX or USB disk?

if you saved your stock unmodded nand, why would you then need to create one?