I/O device error 4gb corona r/w help

chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
hello i have a problem with writing to a corona v2 i read well
and when i write back i get this error.


Nand Initialization Finished
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
Writing to J:\ from D:\X\J-Runner v03 (1) Core Pack\J-Runner\output\nanddump1.bin
The request could not be performed because of an I/O device error.

i have a cr3 pro full post.
any help will much appreciated
 
chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
i'm so sorry i have tried all night to upload images here, i have resized,croped and used the software recommended by Martin C (irfanview) and images have become to small to an extent that me me who resized them cant see them clearly
9kb but stll the site is saing i have exceeded the size that is required. i see big good looking images here but i dont know how you do it. i have finally uploaded them to:
http://feed1.tinypic.com/rss.php?ua=qXE1BPCC4heHKklm78OV2w==
i hope you understand, i've not refused to upload here but its hard for me.
 
chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
http://imgur.com/a/ooKSq

...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
ECC created
Writing to J:\ from D:\X\J-Runner v03 (1) Core Pack\J-Runner\output\image_00000000.ecc
The request could not be performed because of an I/O device error.

Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished
Writing to J:\ from D:\X\J-Runner v03 (1) Core Pack\J-Runner\output\4GB CORONA1\nanddump1.bin
The request could not be performed because of an I/O device error.

Writing to J:\ from D:\X\J-Runner v03 (1) Core Pack\J-Runner\output\4GB CORONA1\nanddump1.bin
The request could not be performed because of an I/O device error.

Writing to J:\ from D:\X\J-Runner v03 (1) Core Pack\J-Runner\output\4GB CORONA1\nanddump1.bin
The request could not be performed because of an I/O device error.

ECC created
Writing to J:\ from D:\X\J-Runner v03 (1) Core Pack\J-Runner\output\image_00000000.ecc
IO operation will not work. Most likely the file will become too long or the handle was not opened to support synchronous IO operations.
Initializing nanddump1.bin..
 
Last edited:
BraveH43

BraveH43

VIP Member
Sep 13, 2008
1,514
0
Somewhere in the 'verse
we are discussing your inability to write to the nand - your pictures are mostly of your glitch chip connections - your nand pcb isn't connected to a ribbon cable (I'm guessing you disconnected it for some reason)
the quality of pic is too poor to see the connections on it.
 
chronixx

chronixx

Senior Member
Jun 12, 2013
144
0
i have changed windows and 7 SD adopters still i can only read but no write.
hopeful when i use another computer, i'll not get the error. because i have used a lot of flux
and i'm sure the qsb is connected well. i have tried to learn from my previous soldering errors and i think now this one is
connected.
 
You must log in or register to reply here.