CORONA Installed CR4 XL, read nand 2x perfectly, now cant connect with J-RP V2 and J-runner

[lonix]

Sorry another suggestion I know it's a pain, with the jrp connected can you check continuity between all the points on the jrp header and the corresponding point on the Xbox?

also

Can you check for voltage at this point

you should have 3.3v

I went back and re read your OP and i believe that you will have to do a bad flash recovery.

It was working fine up untill you wrote the ECC, right?

 

[Mode-B]

first off post a good quality picture of the jr programmer, not saying it's not genuine... Just looking for a possible defect (longshot)... also if you have a multimeter check all of your solder points on the QSB against their corresponding point on the flip side of the board (continuity test).. Also check each point against any and all adjacent points surrounding each point. (so we can almost completely rule out the QSB as the culprit).

One more thing, and it may be stupid because your soldering looks damn near flawless but if you have any doubt about any of your solder bridges (R2C4, R2C6, R2C7, R2C10) or if you are just curious try and touch them up to make sure they are getting bridged properly, I believe they may cause this problem..

OK So I finally got around to running a continuity test on my qsb and every solder point is fine. Also checked for continuity on all my wires installed just incase one was severed for some reason and they all were fine. I also checked all the wires in my jrp connectors and they were fine as well. Got called into work again damn it. I'll have to check all the spots I can on my jrp board itself and see if I can find any bad connections probably tomorrow. Will post back with results.

 

[Mode-B]

Sorry another suggestion I know it's a pain, with the jrp connected can you check continuity between all the points on the jrp header and the corresponding point on the Xbox?

also

Can you check for voltage at this point

you should have 3.3v

I went back and re read your OP and i believe that you will have to do a bad flash recovery.

It was working fine up untill you wrote the ECC, right?

Will have to give it ago tomorrow but will do for sure. And will have to look again for this 3.3v point. Doesn't look familiar. And yes it seemed fine until I wrote the ecc the first attempt didn't work flash config 0x00000000 the immediately after that it wrote the ecc fine it seemed like.

 

[lonix]

In 95% sure it's a bad flash problem, installing a demon can fix this.

 

[Krafter]

In 95% sure it's a bad flash problem, installing a demon can fix this.

Before buying a Demon I suggest you remove the QSB and do a direct wire install. Only do that as the last resort right before buying the Demon though because you will likely destroy the QSB and/or remove solder points on the motherboard if not done properly.

 

[lonix]

That point might be trinity sorry if its not there

Have a read of this thread, by Martin C, I know its old but this should give you an idea of the problem, read part about bad flash recovery

http://team-xecuter.com/forums/showthread.php?77908-Troubleshooting-NAND-X-JRP-Connection-Problems

 

[Mode-B]

Before buying a Demon I suggest you remove the QSB and do a direct wire install. Only do that as the last resort right before buying the Demon though because you will likely destroy the QSB and/or remove solder points on the motherboard if not done properly.

I'm going to purchase a demon once my taxes come in because i have a few phats lying around i can use the cr4 xl on anyway. Just really disappointed becuase alot of peoples work i see looks really sketchy and i mean really sketchy and somehow there getting theres to work. My work looks way better and i have not burned any points or anything and i'm having all kinds of problems. But I'm going to try writing on my xp machine before i do the direct wire install for the programmer. I tested for continuity on the programmer board itself this morning and everything i tested was fine. Also checked for continuity with the programmer connected to the qsb and from the pin headers on the programmer to all the points on the qsb everything checked out fine as well. Hopefully a bad flash recovery isn't to hard lol.

 

[lonix]

You didn't do anything wrong, j-runner stuffed you up.

This has happened to me too, I always load the ecc manually now.

Try this, it's the easiest least risk recovery, but it might not work

Go into jrunner and goto Advanced > custom nand / cr functions

Select write and 16mb
load /common/ECC/CORONA_16MB_CR4.ecc

Have your jr programmer connected and ready to go.

Connect your power supply but have the power lead unplugged

Connect the power and click run simultaneously.

Hopefully it will catch the spi while the smc is still initializing

another method involves bridging some points, then plugging in the power supply


Best of luck with everything hope you get it working soon

 

[Mode-B]

***UPDATE***So after cleaning up the area of the QSB with IPA and using a toothbrush on the board to brush off any solder splash(found a few very small balls of solder) I was able to connect and write to the nand again my nandump1 the same errors on like every block. Then oddly enough my j-runner kept reporting no flash config again. So, I disconnected every cable from everything I was using and let things sit for a day. Then brushed the board a little more and cleaned things with more IPA and was able to connect again and immediately I tried to write my nanddump2 this time and things seemed to be going very smoothly and I didn't see errors on blocks showing up until the very end of the write. I got two errors only this time so instead of trying to reset the programmer i tried to write the ecc cuz I figured if i can boot xell even with the two bad blocks at the end i could at least retrieve my keys to create the the freeboot image and maybe i wouldn't have any problems writing that to the nand. Now after creating the ecc from nanddump2 j-runners giving me errors on all bocks when trying to write it. Then all of the sudden j-runner wont connect now no flash config. I've disconnected everything again and am going to let things sit for a while to see if i can connect again. Seems to connect no problem right away after letting things sit unplugged. Hopefully I'll get it working.


===================================================
Monday, January 19, 2015 11:49:40 AM


J-Runner v0.3 Beta (7) Started




Initializing nanddump1.bin..
Corona
Glitch2 Selected
Nand Initialization Finished
Version: 10
Flash Config: 0x00043000
Writing Nand
nanddump1.bin
Error: 601 writing block 3C
Error: 601 writing block 3E
Error: 601 writing block 3F
Error: 601 writing block 41
Error: 601 writing block 42
Error: 601 writing block 43
Error: 601 writing block 45
Error: 601 writing block 4C
Error: 601 writing block 4F
Error: 601 writing block 50
Error: 601 writing block 60
Error: 601 writing block 82
Error: 601 writing block 2D2
Error: 601 writing block 2D7
Error: 601 writing block 2DA
Error: 601 writing block 2DD
Error: 601 writing block 2DE
Error: 601 writing block 2DF
Error: 681 writing block 2E0
Error: 601 writing block 2E1
Error: 601 writing block 2E2
Error: 601 writing block 2E3
Error: 601 writing block 2E4
Error: 601 writing block 2E5
Error: 601 writing block 2E6
Error: 601 writing block 2E7
Error: 601 writing block 2E8
Error: 601 writing block 2E9
Error: 601 writing block 2EA
Error: 601 writing block 2EB
Error: 601 writing block 2ED
Error: 601 writing block 2EE
Error: 601 writing block 2EF
Error: 601 writing block 2F0
Error: 601 writing block 2F1
Error: 681 writing block 2F2
Error: 601 writing block 2F3
Error: 681 writing block 2F4
Error: 681 writing block 2F5
Error: 601 writing block 2F6
Error: 681 writing block 2F7
Error: 000 writing block 2F8
Error: 000 writing block 2F9
Error: 220 writing block 2FA
Error: 380 writing block 2FB
Error: 000 writing block 2FC
Error: 201 writing block 2FD
Error: 781 writing block 2FE
Error: 751 writing block 2FF
Error: 701 writing block 300
Error: 701 writing block 301
Error: 000 writing block 302
Error: 000 writing block 303
Error: 681 writing block 304
Error: 601 writing block 305
Error: 000 writing block 306
Error: 281 writing block 307
Error: 281 writing block 308
Error: 6C1 writing block 309
Error: 000 writing block 30A
Error: 281 writing block 30B
Error: 000 writing block 30C
Error: 000 writing block 30D
Error: 000 writing block 30E
Error: 000 writing block 30F
Error: 000 writing block 310
Error: 000 writing block 311
Error: 000 writing block 312
Error: 000 writing block 313
Error: 000 writing block 314
Error: 000 writing block 315
Error: 000 writing block 317
Error: 000 writing block 318
Error: 000 writing block 319
Error: 000 writing block 31A
Error: 000 writing block 31B
Error: 000 writing block 31C
Error: 000 writing block 31D
Error: 000 writing block 31E
Error: 000 writing block 31F
Error: 000 writing block 320
Error: 000 writing block 321
Error: 000 writing block 322
Error: 000 writing block 323
Error: 601 writing block 324
Error: 000 writing block 325
Error: 000 writing block 326
Error: 000 writing block 327
Error: 000 writing block 329
Error: 000 writing block 32A
Error: 000 writing block 32B
Error: 000 writing block 32C
Error: 000 writing block 32D
Error: 000 writing block 32E
Error: 00F writing block 32F
Error: 00F writing block 330
Error: 00F writing block 331
Error: 00F writing block 332
Error: 00F writing block 333
Error: 00F writing block 334
Error: 00F writing block 335
Error: 00F writing block 336
Error: 00F writing block 337
Error: 00F writing block 338
Error: 00F writing block 339
Error: 000 writing block 33A
Error: 300 writing block 33B
Error: 7A1 writing block 33C
Error: 601 writing block 33D
Error: 00F writing block 33E
Error: 00F writing block 33F
Error: 000 writing block 340
Error: 701 writing block 341
Error: 000 writing block 342
Error: 00F writing block 343
Error: 00F writing block 344
Error: 00F writing block 345
Error: 00F writing block 346
Error: 00F writing block 347
Error: 300 writing block 348
Error: 00F writing block 349
Error: 00F writing block 34A
Error: 00F writing block 34B
Error: 00F writing block 34C
Error: 000 writing block 34D
Error: 70F writing block 34E
Error: 00F writing block 34F
Error: 00F writing block 350
Error: 00F writing block 351
Error: 00F writing block 352
Error: 00F writing block 353
Error: 00F writing block 354
Error: 00F writing block 355
Error: 00F writing block 356
Error: 00F writing block 357
Error: 00F writing block 358
Error: 00F writing block 359
Error: 00F writing block 35A
Error: 00F writing block 35B
Error: 00F writing block 35C
Error: 00F writing block 35D
Error: 00F writing block 35E
Error: 00F writing block 35F
Error: 00F writing block 360
Error: 00F writing block 361
Error: 00F writing block 362
Error: 00F writing block 363
Error: 00F writing block 364
Error: 00F writing block 365
Error: 00F writing block 366
Error: 00F writing block 367
Error: 00F writing block 368
Error: 00F writing block 369
Error: 00F writing block 36A
Error: 00F writing block 36B
Error: 00F writing block 36C
Error: 30F writing block 36D
Error: 00F writing block 36E
Error: 00F writing block 36F
Error: 00F writing block 370
Error: 00F writing block 371
Error: 00F writing block 372
Error: 00F writing block 373
Error: 00F writing block 374
Error: 00F writing block 375
Error: 00F writing block 376
Error: 00F writing block 377
Error: 00F writing block 378
Error: 00F writing block 379
Error: 00F writing block 37A
Error: 00F writing block 37B
Error: 00F writing block 37C
Error: 00F writing block 37D
Error: 00F writing block 37E
Error: 00F writing block 37F
Error: 00F writing block 380
Error: 00F writing block 381
Error: 00F writing block 382
Error: 00F writing block 383
Error: 00F writing block 384
Error: 00F writing block 385
Error: 00F writing block 386
Error: 00F writing block 387
Error: 00F writing block 388
Error: 00F writing block 389
Error: 00F writing block 38A
Error: 00F writing block 38B
Error: 60F writing block 38C
Error: 00F writing block 38D
Error: 00F writing block 38E
Error: 78F writing block 38F
Error: 78F writing block 390
Error: 00F writing block 391
Error: 00F writing block 392
Error: 00F writing block 393
Error: 00F writing block 394
Error: 00F writing block 395
Error: 00F writing block 396
Error: 00F writing block 397
Error: 00F writing block 398
Error: 00F writing block 399
Error: 00F writing block 39A
Error: 00F writing block 39B
Error: 00F writing block 39C
Error: 00F writing block 39D
Error: 00F writing block 39E
Error: 00F writing block 39F
Error: 00F writing block 3A0
Error: 00F writing block 3A1
Error: 00F writing block 3A2
Error: 00F writing block 3A3
Error: 00F writing block 3A4
Error: 00F writing block 3A5
Error: 00F writing block 3A6
Error: 00F writing block 3A7
Error: 00F writing block 3A8
Error: 00F writing block 3A9
Error: 00F writing block 3AA
Error: 00F writing block 3AB
Error: 00F writing block 3AC
Error: 00F writing block 3AD
Error: 00F writing block 3AE
Error: 00F writing block 3AF
Error: 00F writing block 3B0
Error: 000 writing block 3B1
Error: 00F writing block 3B2
Error: 00F writing block 3B3
Error: 00F writing block 3B4
Error: 00F writing block 3B5
Error: 00F writing block 3B6
Error: 00F writing block 3B7
Error: 00F writing block 3B8
Error: 00F writing block 3B9
Error: 00F writing block 3BA
Error: 00F writing block 3BB
Error: 00F writing block 3BC
Error: 00F writing block 3BD
Error: 00F writing block 3BE
Error: 00F writing block 3BF
Error: 00F writing block 3C0
Error: 00F writing block 3C1
Error: 00F writing block 3C2
Error: 00F writing block 3C3
Error: 00F writing block 3C4
Error: 00F writing block 3C5
Error: 00F writing block 3C6
Error: 00F writing block 3C7
Error: 00F writing block 3C8
Error: 00F writing block 3C9
Error: 00F writing block 3CA
Error: 00F writing block 3CB
Error: 00F writing block 3CC
Error: 00F writing block 3CD
Error: 00F writing block 3CE
Error: 00F writing block 3CF
Error: 00F writing block 3D0
Error: 00F writing block 3D1
Error: 00F writing block 3D2
Error: 00F writing block 3D3
Error: 00F writing block 3D4
Error: 00F writing block 3D5
Error: 00F writing block 3D6
Error: 00F writing block 3D7
Error: 00F writing block 3D8
Error: 00F writing block 3D9
Error: 00F writing block 3DA
Error: 00F writing block 3DB
Error: 00F writing block 3DC
Error: 00F writing block 3DD
Error: 00F writing block 3DE
Error: 00F writing block 3DF
Error: 00F writing block 3E0
Error: 00F writing block 3E1
Error: 00F writing block 3E2
Error: 781 writing block 3E3
Error: 380 writing block 3E4
Error: 00F writing block 3E5
Error: 00F writing block 3E6
Error: 00F writing block 3E7
Error: 00F writing block 3E8
Error: 00F writing block 3E9
Error: 00F writing block 3EA
Error: 00F writing block 3EB
Error: 00F writing block 3EC
Error: 00F writing block 3ED
Error: 00F writing block 3EE
Error: 00F writing block 3EF
Error: 00F writing block 3F0
Error: 00F writing block 3F1
Error: 00F writing block 3F2
Error: 00F writing block 3F3
Error: 00F writing block 3F4
Error: 00F writing block 3F5
Error: 00F writing block 3F6
Error: 00F writing block 3F7
Error: 00F writing block 3F8
Error: 00F writing block 3F9
Error: 00F writing block 3FA
Error: 00F writing block 3FB
Error: 00F writing block 3FC
Error: 00F writing block 3FD
Error: 00F writing block 3FE
Error: 00F writing block 3FF
Done!
in 4:07 min:sec


Version: 10
Flash Config: 0x3F03803F
Writing Nand
nanddump1.bin
Error: 000 writing block 0
Error: 007 writing block 1
Error: 007 writing block 2
Error: 007 writing block 3
Error: 000 writing block 4
Error: 000 writing block 5
Error: 007 writing block 6
Error: 007 writing block 7
Error: 007 writing block 8
Error: 007 writing block 9
Error: 007 writing block A
Error: 007 writing block B
Error: 000 writing block C
Error: 000 writing block D
Error: 007 writing block E
Error: 007 writing block F
Error: 007 writing block 10
Error: 007 writing block 11
Error: 000 writing block 12
Error: 007 writing block 13
Done!
in 0:07 min:sec


Version: 07
Wrong Version.
Version: 10
Flash Config: 0x00000010
Writing Nand
nanddump1.bin
IoTimedOut
Error: 000 writing block 0
Error: 007 writing block 1
Error: 000 writing block 2
Error: 000 writing block 3
Error: 000 writing block 4
Error: 000 writing block 5
Error: 000 writing block 6
Error: 000 writing block 7
Error: 000 writing block 8
Error: 000 writing block 9
Error: 000 writing block A
Error: 000 writing block B
Error: 000 writing block C
Error: 000 writing block D
Error: 000 writing block E
Error: 000 writing block F
Error: 000 writing block 10
Error: 000 writing block 11
Error: 000 writing block 12
Error: 000 writing block 13
Error: 000 writing block 14
Done!
in 0:07 min:sec


Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Initializing nanddump1.bin..
Corona
Nand Initialization Finished
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Could not find a part of the path.


No internet connection found (RasInstalled), so can't check integrity of files. Use at your own risk
===================================================
Monday, January 19, 2015 11:57:48 AM


J-Runner v0.3 Beta (7) Started




Initializing nanddump1.bin..
Corona
Glitch2 Selected
Nand Initialization Finished
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Corona Manually Selected
You need an .bin image


No internet connection found (RasInstalled), so can't check integrity of files. Use at your own risk
===================================================
Monday, January 19, 2015 11:59:52 AM


J-Runner v0.3 Beta (7) Started




Corona Manually Selected
You need an .bin image
Initializing nanddump2.bin..
Corona
Glitch2 Selected
Nand Initialization Finished
Version: 10
Flash Config: 0x00000000
Can not Continue
ECC created
You need an .bin image


No internet connection found (RasInstalled), so can't check integrity of files. Use at your own risk
===================================================
Monday, January 19, 2015 12:14:34 PM


J-Runner v0.3 Beta (7) Started




Initializing nanddump1.bin..
Corona
Glitch2 Selected
Nand Initialization Finished
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Shutdown
Version: 10
Flash Config: 0x00000000
Can not Continue
Power Up
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Power Up
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Device Not Found.
Device Not Found.
Device Not Found.
Device Not Found.
Device Not Found.
Device Not Found.
Device Not Found.
Device Not Found.
Device Not Found.
Device Not Found.


No internet connection found (RasInstalled), so can't check integrity of files. Use at your own risk
===================================================
Monday, January 19, 2015 12:22:23 PM


J-Runner v0.3 Beta (7) Started




Initializing nanddump1.bin..
Corona
Glitch2 Selected
Nand Initialization Finished
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Corona Manually Selected
Version: 10
Flash Config: 0x00000000
Can not Continue
Initializing nanddump1.bin..
Corona
Nand Initialization Finished
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Initializing nanddump1.bin..
Corona
Nand Initialization Finished
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Shutdown
Version: 10
Flash Config: 0x00000000
Can not Continue
Power Up
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue


No internet connection found (RasInstalled), so can't check integrity of files. Use at your own risk
===================================================
Tuesday, January 20, 2015 11:38:55 AM


J-Runner v0.3 Beta (7) Started




Initializing nanddump2.bin..
Corona
Glitch2 Selected
Nand Initialization Finished
Device Not Found.
Device Not Found.
Initializing nanddump2.bin..
Corona
Nand Initialization Finished
Device Not Found.
Version: 10
Flash Config: 0x00043000
Writing Nand
nanddump2.bin
Error: 601 writing block 3B3
Error: 601 writing block 3B4
Done!
in 3:40 min:sec


Corona Manually Selected
Version: 00
Wrong Version.
Initializing nanddump2.bin..
Corona
Nand Initialization Finished
ECC created
Version: 10
Flash Config: 0x00000010
Writing Nand
image_00000000.ecc
IoTimedOut
Error: 000 writing block 0
Error: 204 writing block 2
Error: 432 writing block 3
Error: 432 writing block 4
Error: 432 writing block 5
Error: 634 writing block 6
Error: 006 writing block 7
Error: 630 writing block 8
Error: 006 writing block 9
Error: 630 writing block A
Error: 206 writing block B
Error: 862 writing block C
Error: 000 writing block D
Error: 000 writing block E
Error: 000 writing block F
Error: 000 writing block 10
Error: 000 writing block 11
Error: 000 writing block 12
Error: 000 writing block 13
Error: 000 writing block 14
Error: 000 writing block 15
Error: 000 writing block 16
Error: 000 writing block 17
Error: 000 writing block 18
Error: 000 writing block 19
Error: 000 writing block 1A
Error: 000 writing block 1B
Error: 000 writing block 1C
Error: 000 writing block 1D
Error: 000 writing block 1E
Error: 000 writing block 1F
Error: 000 writing block 20
Error: 000 writing block 21
Error: 000 writing block 22
Error: 000 writing block 23
Error: 000 writing block 24
Error: 000 writing block 25
Error: 000 writing block 26
Error: 000 writing block 27
Error: 000 writing block 28
Error: 000 writing block 29
Error: 000 writing block 2A
Error: 000 writing block 2B
Error: 000 writing block 2C
Error: 000 writing block 2D
Error: 000 writing block 2E
Error: 000 writing block 2F
Error: 000 writing block 30
Error: 000 writing block 31
Error: 000 writing block 32
Error: 000 writing block 33
Error: 000 writing block 34
Error: 000 writing block 35
Error: 000 writing block 36
Error: 000 writing block 37
Error: 000 writing block 38
Error: 000 writing block 39
Error: 000 writing block 3A
Error: 000 writing block 3B
Error: 000 writing block 3C
Error: 000 writing block 3D
Error: 000 writing block 3E
Error: 000 writing block 3F
Error: 000 writing block 40
Error: 000 writing block 41
Error: 000 writing block 42
Error: 000 writing block 43
Error: 000 writing block 44
Error: 000 writing block 45
Error: 000 writing block 46
Error: 000 writing block 47
Error: 000 writing block 48
Error: 000 writing block 49
Error: 000 writing block 4A
Error: 000 writing block 4B
Error: 000 writing block 4C
Error: 000 writing block 4D
Error: 000 writing block 4E
Error: 000 writing block 4F
Done!
in 0:25 min:sec


You need an .ecc image
Initializing nanddump2.bin..
Corona
Nand Initialization Finished
ECC created
Version: 00
Wrong Version.
Version: 10
Flash Config: 0x00000010
Writing Nand
image_00000000.ecc
IoTimedOut
Error: 000 writing block 0
Error: 000 writing block 1
Error: 000 writing block 2
Error: 000 writing block 3
Error: 000 writing block 4
Error: 000 writing block 5
Error: 000 writing block 6
Error: 000 writing block 7
Error: 000 writing block 8
Error: 000 writing block 9
Error: 000 writing block A
Error: 000 writing block B
Error: 000 writing block C
Error: 000 writing block D
Error: 000 writing block E
Error: 000 writing block F
Error: 000 writing block 10
Error: 000 writing block 11
Error: 000 writing block 12
Error: 000 writing block 13
Error: 000 writing block 14
Error: 000 writing block 15
Error: 000 writing block 16
Error: 000 writing block 17
Error: 000 writing block 18
Error: 000 writing block 19
Error: 000 writing block 1A
Error: 000 writing block 1B
Error: 000 writing block 1C
Error: 000 writing block 1D
Error: 000 writing block 1E
Error: 000 writing block 1F
Error: 000 writing block 20
Error: 000 writing block 21
Error: 000 writing block 22
Error: 000 writing block 23
Error: 000 writing block 24
Error: 000 writing block 25
Error: 000 writing block 26
Error: 000 writing block 27
Error: 000 writing block 28
Error: 000 writing block 29
Error: 000 writing block 2A
Error: 000 writing block 2B
Error: 000 writing block 2C
Error: 000 writing block 2D
Error: 000 writing block 2E
Error: 000 writing block 2F
Error: 000 writing block 30
Error: 000 writing block 31
Error: 000 writing block 32
Error: 000 writing block 33
Error: 000 writing block 34
Error: 000 writing block 35
Error: 000 writing block 36
Error: 000 writing block 37
Error: 000 writing block 38
Error: 000 writing block 39
Error: 000 writing block 3A
Error: 000 writing block 3B
Error: 000 writing block 3C
Error: 000 writing block 3D
Error: 000 writing block 3E
Error: 000 writing block 3F
Error: 000 writing block 40
Error: 000 writing block 41
Error: 000 writing block 42
Error: 000 writing block 43
Error: 000 writing block 44
Error: 000 writing block 45
Error: 000 writing block 46
Error: 000 writing block 47
Error: 000 writing block 48
Error: 000 writing block 49
Error: 000 writing block 4A
Error: 000 writing block 4B
Error: 000 writing block 4C
Error: 000 writing block 4D
Error: 000 writing block 4E
Error: 000 writing block 4F
Done!
in 0:25 min:sec


You need an .ecc image
ECC created
Version: 00
Wrong Version.
Version: 10
Flash Config: 0x00000010
Writing Nand
image_00000000.ecc
IoTimedOut
Error: 000 writing block 0
Error: 000 writing block 1
Error: 000 writing block 2
Error: 000 writing block 3
Error: 000 writing block 4
Error: 000 writing block 5
Error: 000 writing block 6
Error: 000 writing block 7
Error: 000 writing block 8
Error: 000 writing block 9
Error: 000 writing block A
Error: 000 writing block B
Error: 000 writing block C
Error: 000 writing block D
Error: 000 writing block E
Error: 000 writing block F
Error: 000 writing block 10
Error: 000 writing block 11
Error: 000 writing block 12
Error: 000 writing block 13
Error: 000 writing block 14
Error: 000 writing block 15
Error: 000 writing block 16
Error: 000 writing block 17
Error: 000 writing block 18
Error: 000 writing block 19
Error: 000 writing block 1A
Error: 000 writing block 1B
Error: 000 writing block 1C
Error: 000 writing block 1D
Error: 000 writing block 1E
Error: 000 writing block 1F
Error: 000 writing block 20
Error: 000 writing block 21
Error: 000 writing block 22
Error: 000 writing block 23
Error: 000 writing block 24
Error: 000 writing block 25
Error: 000 writing block 26
Error: 000 writing block 27
Error: 000 writing block 28
Error: 000 writing block 29
Error: 000 writing block 2A
Error: 000 writing block 2B
Error: 000 writing block 2C
Error: 000 writing block 2D
Error: 000 writing block 2E
Error: 000 writing block 2F
Error: 000 writing block 30
Error: 000 writing block 31
Error: 000 writing block 32
Error: 000 writing block 33
Error: 000 writing block 34
Error: 000 writing block 35
Error: 000 writing block 36
Error: 000 writing block 37
Error: 000 writing block 38
Error: 000 writing block 39
Error: 000 writing block 3A
Error: 000 writing block 3B
Error: 000 writing block 3C
Error: 000 writing block 3D
Error: 000 writing block 3E
Error: 000 writing block 3F
Error: 000 writing block 40
Error: 000 writing block 41
Error: 000 writing block 42
Error: 000 writing block 43
Error: 000 writing block 44
Error: 000 writing block 45
Error: 000 writing block 46
Error: 000 writing block 47
Error: 000 writing block 48
Error: 000 writing block 49
Error: 000 writing block 4A
Error: 000 writing block 4B
Error: 000 writing block 4C
Error: 000 writing block 4D
Error: 000 writing block 4E
Error: 000 writing block 4F
Done!
in 0:25 min:sec


ECC created
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue


No internet connection found (RasInstalled), so can't check integrity of files. Use at your own risk
===================================================
Tuesday, January 20, 2015 11:51:52 AM


J-Runner v0.3 Beta (7) Started




WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button


Initializing nanddump2.bin..
Corona
Glitch2 Selected
Nand Initialization Finished
ECC created
Version: 10
Flash Config: 0x00000000
Can not Continue
Version: 10
Flash Config: 0x00000000
Can not Continue

 

[Krafter]

Sounds to me like there's debris or a buildup of flux under the QSB.

 

[Mode-B]

Sounds to me like there's debris or a buildup of flux under the QSB.

Was just thinking that...Need an air can and hopefully works and wont have to de-solder the qsb.

 

[Krafter]

If that is the case then you'll have to remove the QSB. You'll never get under it with air.

The best way to remove one is to get a bit of wax paper. Heat a joint up with your iron and work the wax paper under it. Some points are easier than others but if you work at it long enough then you can remove it without damage.

 

[Mode-B]

If that is the case then you'll have to remove the QSB. You'll never get under it with air.

The best way to remove one is to get a bit of wax paper. Heat a joint up with your iron and work the wax paper under it. Some points are easier than others but if you work at it long enough then you can remove it without damage.

Gonna give it a go as soon as I get home.

 

[Krafter]

Then do a wire install to read the NAND and see how it goes.

 

[Mode-B]

Then do a wire install to read the NAND and see how it goes.

I already read and wrote to the nand plenty just trying to write the stock nanddump and get the ecc on there but will do...cant hurt.

 

[stucknvegas]

That many bad blocks reading or writing to Corona Bad solder connections Before you proceed in destroing that QSB Try to touch up the soldering
The ones that matter the most are in the 2 rows next to the JWP stamped on the QSB ---5 connections the one close to JWP is the ground and it requires much more heat than the rest

 

[Krafter]

What has me thinking that it's an issue under the QSB is the fact that he lets it sit for a while, comes back and it will read. Its like its building up a charge. I'm not saying 100% that is the problem but I've seen similar issue but it can't hurt to touch up the joints first.

 

[stucknvegas]

I have had that same issue after 16M/B nand conversion on Corona He can also look close around the nand and South bridge for solder splash and possible damaged SMD caps and resistors

 

[lonix]

Use solder wick to remove as much of the excess solder from the QSB as possible, then do the baking paper trick, try to get a bit of heat into the QSB to loosen any double sided tape

 

[Mode-B]

***UPDATE***
Finally the forums are back up! Alright so I was bored and started working on my box again and FINALLY SUCCESS!!!!!! I didn't think I was going to be able to de-solder my QSB without messing something up or lifting a trace so I just went over my work and removed as much solder on the QSB points as I could which didn't help anything it still was connecting here and there only with errors. Decided to go ahead and de-solder the QSB which was a lot easier than I anticipated working wax paper under the points. I did break a trace on the bottom of the QSB but wasn't worried as I could fix it. Took off the QSB and there was quite a bit of flux under it that I wasn't able to get to to clean up with it in place. I cleaned the nand points and went ahead and did the direct wire install and guess what? no effing problems at all connecting now in j-runner. AWESOME! Only thing after that was now every time I wrote the ecc I created I was getting errors on two of the blocks. Without doing any research or anything I was browsing the j-runner common folder where I found a corona cr4 ecc file so I tried that and BAM I got it to glitch into Xell and retrieve my cpu key. What a damn relief it was when I got no errors at all. Went ahead and created my xebuild image and got it up and glitching. As of now it seems a little slow though...it was almost instaboot at first few boots but now takes about 10 or 11 seconds to bootup. Not a problem though I'll just mess with the dips and caps on the cr4 to get better timing on the boot. Other than that only thing I need to do now is drop my xebuild image down to a kernel lower because for some reason the Dashlaunch(3.13 I think) that supposedly supports the kernel I have in mine currently(16747 I believe I'm at work at the moment so I don't have the info in front of me) isn't working at all for some reason and the one I tried to install with FSD 3 says it didn't support my kernel so couldn't install. Would really like dashlaunch so I can boot right into FSD. Other than that super siked to have it working and I want to thank everyone that has given me input on this thread. I REALLY APPRECIATE all the good info and feedback I got. I shouldn't have a problem doing the other stuff now. So again... MANY THANKS! to all who contributed.

I'll just bypass the damn QSB if I do another one LMFAO.

Now on to all the fun stuff.