ip won't stick

[halo117]

I just bought a xlcd and pro switch. I installed them and flashed the 1959 bios to the 1 meg bank, now I can't get the ip address to stick. I have had the same ip everytime i booted before now it will flash a diffrent ip from the first and only one i've ever had. it flashes on and off the screen about every 2 seconds. Any help would be great.
Thanks


Halo117

 

[yourM0M]

bad network cable maybe

 

[Jzor]

just set a static IP

 

[yourM0M]

he's saying flashes....if the router if he even has one is constantly updating the ip then id return that bitch

 

[Limey]

Does the mac address change too? Many people ar ehaving this problem after going to 1959.

I just posted this, did someone delete it?

 

[halo117]

I will have to check I am not sure.

 

[junior]

Help With Unbricking My Lite-On 74850c Drive Help Please

Hello Everyone My Name Is Mike


I Have a lite-On 7458c Drive That's Bricked I Have Use This Tutorial Below And The Link Is There

I used Iprep 009 To Make The USB Boot Device
The Device Is A Scan Disk 2 GB
I have A VT6421A SATA Card
CK3 Pro With Probe
I'm Running Windows XP SP2 Upgraded To SP3 Media Edition
Jungle Flasher 1.60 Beta

Robin Hoods Playground



I Have Read Through The Tutorial And Followed It Correctly Until I Got To The Part Where It Says
Erasing Finished!
Then It SAYS NOW TURN YOUR LITE-ON OFF TEN BACK ON
And Then Its Say PRESS ANY KEY TO CONTINUE



Question Do I Turn My Drive On And Off Before I Press Any Key To Continue or After I Press Continue?

Next Its Say

0)0x01DF0 IDE Pri Master None
1)0x01F IDE Pri Slave ATAPI Philips DVD+/-RW DVD8801 4D28
MTK Vendor Intro Failed On Port 0x01F0.
If You Choose To Resend The Command You Should Turn The Device Off And On After You Pressed "Yes"
Do You Want To Resend The Command Until The Drive Responds (Y/N)? If I Choose Yes The Status Code It Flickers Between 50 And 51.
Then I Would Choose Abort Because I Let It Flicker For Like Two Minutes

Then It Say This After I Click ESC To Abort

Flash Manufacturer ID: 0x00, DeviceID: 0x00
Flash Type: MTK Vendor Intro Failed
Flash Size: 0 Bytes (0 KB)
2) 0x0170 IDE Sec Master None
3) 0x0170 IDE Sec Master None
4) 0xB8A0 SATA Pri Master ATAPI No Identify Possible
Flash Manufacturer ID: 0xEF, DeviceID: 0x011
Flash Type: Winbond/NEX(W25P20/W25X20/NX25P20)
Flash Size: 262144 Bytes (256 KB)
5) 0xB8B0 SATA Pri Master None
6) 0xB8C0 IDE Pri Master None
7) 0xB8C0 IDE Pri Slave None

Enter The Number Of An ATAPI Drive:


It Keeps Giving Me A Failed Help Please

 

[ckam]

Re: Help With Unbricking My Lite-On 74850c Drive Help Please

the tutorial robin hoods playground should have worked ima try and simplify the tutorial for you, make your new bootable usb with iprep again, and try it out. Now connect power to ur drive, and leave a sata cable (one side connect to computer) in hand for when you need it and then make the tray half open you know eject and then close and as its closing disconnect power and then reconnect(that was all done without the sata cable leaving ur computer alone). Now you go to ur computer boot from usb and then connect sata cable to drive while ur xbox is still with half tray open. Then follow instrctions on screen/website(make sure u get ur file names exactly like their supposed to be). Hope this helps. Good luck