RGH Is it slow boot time?

[Danielravelo]

Hello guys, I recently installed a coolrunner on my xbox and a qsb upgraded (with the crystal) as of trying to do rgh 2 to my console since its a corona v1. From the begining everything went smooth, even the soldering. I started my j-runner and hooked it up with the JR programmer v2 and from there to the qsb upgraded. I pressed F2 on the computer and gave me just what I was expecting:
flash config 0x00043000
CB version 13181
Corona
(I guess this means the soldering is good)
Then I read the nands without problems, created the .ecc and wroted to the nand.
Then I programed my coolrunner with the timing file.
But when I went to test it, it simply didn't show the green light at all.
I was wondering if this is a boot time issue?
Should I try some combinations?
Is there any other issue that might be causing the coolrunner not to show its green light?

This is all I'm working with:
Corona v1
JR programmer
QSB corona upgraded
J-Runner
CR rev C
(JP closed 3-2 closed too, switched to slim, cpu_rst is the 55 cm long blue wire)
Thanks

 

[gavin_darkglide]

Which timing file have you tried?

 

[Danielravelo]

I have tried 0-2. 1-2. And 3-3

 

[Utmad]

Complete the rgh template in my sig for support

 

[Danielravelo]

RGH TEMPLATE
Corona v1
JR programmer
QSB corona add on ( crystal)
Coolrunner Rev C
Nand size 16mb
dash version 2.0.16537.0
CB version 13181

 

[ultimate360]

You sure you wrote actual ecc? I screwed up once and wrote a JTAG xell image to the nand and didn't get a debug light... Ah, good times

 

[Danielravelo]

Yeah... I'm pretty sure I wrote the right ecc file.
In addition, I read the nand and flashed the coolrunner with the console plugued in to the power supply but not turned on.
I read in some post that u can't do that, but that's how it worked for me.
Thanks for any help.

 

[ultimate360]

That's fine. Post your JR log and pics of your soldering. Shouldn't be hard to rule out the problem here

 

[Danielravelo]

Thanks for your help ultimate360, I'll be back at noon I'm working right now

 

[Danielravelo]

Hello guys, its been a while. Right now I'm doing a nand reading to come up with tge log but this is weird, now, after identifying the motherboard as a Corona v1, it says its a Trinity.

 

[nofeloniesyet]

Hello guys, its been a while. Right now I'm doing a nand reading to come up with tge log but this is weird, now, after identifying the motherboard as a Corona v1, it says its a Trinity.

it will do that if ecc is written to nand,as we use the trinity bootloader to get xell.so this is 100% normal

 

[Danielravelo]

it will do that if ecc is written to nand,as we use the trinity bootloader to get xell.so this is 100% normal

Wow thank god.
Anyway guys here is the j-runner log without the nand reading process. I just loaded the two previously read nands:

- - - Updated - - -

Ill come up with the pictures right now.

 

[Danielravelo]

Hope this works.
thanks.

 

[ultimate360]

And there goes the support... Sorry, you have a clone CR which is not supported here.

 

[Danielravelo]

Ohhhhh noooooooo, can't belive it, how do u know its a clone?
Is there any special features that makes clones different from the originals? What are those?

 

[ultimate360]

The differences are pretty apparent, here is a genuine CR: https://www.dropbox.com/sc/fkyju9oikwfda0z/AADz_Gi5jlydAzNsm82LfVg3a

Observe the colors, corners, main chip, switch colors, and printing.

 

[morinzo]

the corona qsb cr upgrade doesn't look right either..

 

[Sasuke Uchiha]

tyour best option is to either get a slim proto or a x360ace. slim proto u will get support here but the ace u won

 

[morinzo]

I have tried the ace and personally think its garbage.. Personally I'm using S****t 2.0 till the CR4 comes out because I cant find any TX chips right now..

 

[ultimate360]

the corona qsb cr upgrade doesn't look right either..

Looks fine to me, the recent batch i just ordered looks like that. clones of that thing cost twice the price of original ones anyways lol