RGH J-R programmer error writing

[Argentum]

I am facing a lot of difficulties with the jr programmer I need to restart it lots and it gives me 0x00000 flash configuration many times and after restarting a couple of times and plugging unplugging i can manage to write.

the issue i am facing now is the following when trying to write the ECC on a trinity:

===================================================
Monday, June 11, 2012 5:03:12 PM

J-Runner v0.2 Beta (276) Started



Checking Files
Finished Checking Files
Arm Version: Version: 01
Flash Config: 0x00023010
Writing Nand
Error: 280 writing block 0
Error: 280 writing block 1
Error: 280 writing block 2
Error: 000 writing block 3
Error: 621 writing block 4
Error: 000 writing block 5
Error: 621 writing block 6
Error: 021 writing block 7
Error: 000 writing block 8
Error: 001 writing block 9
Error: 601 writing block A
Error: 601 writing block B
Error: 601 writing block C
Error: 601 writing block D
Error: 000 writing block E
Error: 601 writing block F
Error: 001 writing block 10
Error: 000 writing block 11
Error: 000 writing block 12
Error: 000 writing block 13
Error: 000 writing block 14
Error: 000 writing block 15
Error: 000 writing block 16
Error: 000 writing block 17
Error: 000 writing block 18
Error: 000 writing block 19
Error: 000 writing block 1A
Error: 000 writing block 1B
Error: 000 writing block 1C
Error: 000 writing block 1D
Error: 000 writing block 1E
Error: 000 writing block 1F
Error: 000 writing block 20
Error: 000 writing block 21
Error: 000 writing block 22
Error: 000 writing block 23
Error: 621 writing block 24
Error: 000 writing block 25
Error: 621 writing block 26
Error: 000 writing block 27
Error: 021 writing block 28
Error: 000 writing block 29
Error: 000 writing block 2A
Error: 000 writing block 2B
Error: 000 writing block 2C
Error: 000 writing block 2D
Error: 000 writing block 2E
Error: 000 writing block 2F
Error: 000 writing block 30
Error: 000 writing block 31
Error: 000 writing block 32
Error: 000 writing block 33
Error: 000 writing block 34
Error: 000 writing block 35
Error: 000 writing block 36
Error: 621 writing block 37
Error: 000 writing block 38
Error: 000 writing block 39
Error: 000 writing block 3A
Error: 000 writing block 3B
Error: 000 writing block 3C
Error: 000 writing block 3D
Error: 000 writing block 3E
Error: 000 writing block 3F
Error: 000 writing block 40
Error: 000 writing block 41
Error: 000 writing block 42
Error: 000 writing block 43
Error: 000 writing block 44
Error: 000 writing block 45
Error: 000 writing block 46
Error: 000 writing block 47
Error: 000 writing block 48
Error: 000 writing block 49
Error: 021 writing block 4A
Error: 000 writing block 4B
Error: 000 writing block 4C
Error: 000 writing block 4D
Error: 601 writing block 4E
Error: 000 writing block 4F
Done!

 

[Martin C]

Pics are needed - VIPs need to follow the rules too, you know.

 

[Teajunkie]

Martin you gone soft???

 

[Martin C]

Got called away from my PC

 

[Argentum]

I didn't know that it's an infraction to post without a pic. as it's not mentioned in the 10 rules you just directed me to.

Anyway, I will post one now I just wanted to add the following. This problem happened after I obtained 2 similar bad block free dumps and wrote the ECC.

But it refused to turn on although I could hear the beeps but lights and fan wont start. I wrote the original NAND and it turned on. I recreated the ECC and using the same solder it refuses to write using j runner. I tried to use XNANDhealer but when I try to Detect the nand NANDpro30 stops responding, Try again in j runner no success.

Then using the same solder I re opened J-runner to try and re-write the ECC to copy the error message and it writes successfully.:crazy: (using the same solder)

Is the problem wit my j runner or software issues, bit this was not happening before

 

[Martin C]

It should be common sense. By looking at that pic, you've given this a few attempts at soldering already, so no telling what you've done to where.

Use my NAND-x troubleshooting link to check the values of the points you've soldered to.

 

[GSIBOY]

Had sort of the same problem, trim the wires and then tin them and then try, also shorten the wires, they way to long

Sent from my GT-I9100 using Tapatalk 2

 

[zackf89]

Can u read the NAND?

 

[Urban Gamer]

I had this issue when I first did mine and after using the search button I found a few different threads and what I found worked is if in J-Runner go into settings and increase the delay. 2 was good for me but it may be higher or lower for you. Perfect writing since.