RGH J-Runner and ST NAND128W3A28N6 issue -can not continue

C

costinradu

Full Member
Dec 2, 2009
43
0
Nirvana
I tried to read the NAND of a Trinity board with the new ST NAND128W3A28N6.I use Nand-x V3 and J-Runner on the latest dashboard.I only get "can not continue" message.I tried with Nandpro3 also but no result.I checked solder points several times.All good.I suspected the Nand X to be faulty but i use it on another Trinity board with the old Hynix NAND and all work great.I really don't know what is the problem.I put together all xbox parts and everything work.No problem with the mainboard.I'm not on the first RGH.Something is diferent with this new NAND?
 
Last edited:
  • Like
Reactions: Gogu
C

costinradu

Full Member
Dec 2, 2009
43
0
Nirvana
soldering is good.is not my first rgh.with hynix it work.tomorow i will upload some photos.but i think is a compatibility isue with the new NAND
 
  • Like
Reactions: Gogu
Modz Inc

Modz Inc

BANNED
Dec 26, 2011
98
0
try using coolshrimp instead or reboot your PC...sometimes it gives some problems to detect
 
Ubergeek

Ubergeek

Xecuter Groupie
Feb 24, 2003
6,259
0
California, USA
he is right - SPI read bombs out with this nand

we actually have one of these to work with - stay tuned

---------- Post added at 02:55 ---------- Previous post was at 02:48 ----------

this is a Corona board btw - not Trinity
 
C

costinradu

Full Member
Dec 2, 2009
43
0
Nirvana
Ubergeek said:
he is right - SPI read bombs out with this nand

we actually have one of these to work with - stay tuned

---------- Post added at 02:55 ---------- Previous post was at 02:48 ----------

this is a Corona board btw - not Trinity
Click to expand...
Corona?Why?It have Hanah chip and 10.83A power
 
  • Like
Reactions: Gogu
A

axelll

VIP Member
Mar 1, 2011
469
17
Everywhere
If your DVD drive is from 09.2011 then the board is 100 % since almost all the boards after 08.2011 are Coronas. Post a pic with the front board, where HANA chip is supposed to be.
 
C

costinradu

Full Member
Dec 2, 2009
43
0
Nirvana
axelll said:
If your DVD drive is from 09.2011 then the board is 100 % since almost all the boards after 08.2011 are Coronas. Post a pic with the front board, where HANA chip is supposed to be.
Click to expand...
Where is"supposed" to be???
Pal, i know i'm talking about.Is a Trinity board, with Hana chip and 10.83A power.It must be a compatibility isue with the new Nand.
I tried with XP to.Same sh*t.J-Runner "can not continue" over and over again.
 
Last edited:
  • Like
Reactions: Gogu
A

axelll

VIP Member
Mar 1, 2011
469
17
Everywhere
You're right, anyway, HANA chip on this board is strange(I'm talking about MFD), theoretically, you should be able to read a clean nand. As ubergeek said, "we actually have one of these to work with - stay tuned"
 
  • Like
Reactions: costinradu
C

costinradu

Full Member
Dec 2, 2009
43
0
Nirvana
better pictures oh Hana chip and ST-NAND
Update!
I just verified all the traces from solder points to first point of mainboard.Everything ok.I just eliminated the presumption of cut traces by mistake.
My console-modder pal confirmed that Trinity with the same NAND (ST) but MFD 2011-04-06 it work.
We test it my motherboard with his tools and same results. "Can not continue".We think it is a revision issue.
 
Last edited:
  • Like
Reactions: Gogu
You must log in or register to reply here.