Jasper 0022 need advise

[SOloNon]

have jasper 0022 , need advise for fix it , dont have pic cause i sent it to the mod but he cant fix it , i recomended to reflow or reball and he refuse , he said there is no caps or resistors fryed but also cant repair it . secendry code apear about 30 sec . gpu and cpu geting temputry . any advise would be grateful and i shall tell him to do . sorry for none pics but if any thing you can tell me there is chance to fix it . thank you :frown:

 

[-DoC-]

Assuming this was not RGH'd prior with a bad nand I have had luck fixing 0022 with a GPU reball. I've also had about 4 0022's that I couldn't repair. If you had screw and washers on this console good luck fixing it now. I've never had much luck after someone attempted repairs prior.

 

[SOloNon]

yes agree with you but he only checked caps an resistors with multimeter and did not more and i think it's because high voltage cause this rrod happened when i add 670 pf inline on cpu rst . and i know something was fryed

 

[-DoC-]

I wish you luck....Those damn 0022's can be so frustrating. A reflow of the GPU/CPU is easy and I usually try as a last ditch effort before scrapping the board.

 

[SOloNon]

Thank you , i think no one helping me cause i dont have pics :redface: but im Desperate

 

[weegaza2k9]

have jasper 0022 , need advise for fix it , dont have pic cause i sent it to the mod but he cant fix it , i recomended to reflow or reball and he refuse , he said there is no caps or resistors fryed but also cant repair it . secendry code apear about 30 sec . gpu and cpu geting temputry . any advise would be grateful and i shall tell him to do . sorry for none pics but if any thing you can tell me there is chance to fix it . thank you :frown:

dont reball or reflow, just make sure you have patchsmc enabled in XeBuild and it will fix, I messed up my falcons trace thinking it was my HANA chip. Repaired and patched smc, worked first time!

EDIT:

Mine was a 0022 Error aswell it just sat there looking at me for 30 secs then 0022.

 

[SOloNon]

I dont think so , cause 2 time i back to stock and everything was fine and then i worked some more on console , never can't run xell but after that when i wants back to stock secendry code appeared. is it possible smc got problem during the work ?????

 

[KhaineGB]

Could be an incorrect LDV value too.

 

[SOloNon]

yes but not in this case cause as i know when it's about ldv secendry code should be appear less than 15 seceneds . i never updated dash during the work also when martin posted ldv's topic i dupted and i checked too,

 

[LordTheron]

Hi there,

You can check if gpu needs reballor is burnt without taking the chip off.

see the link below, last picture at the bottom shows where to check and if you get around 2ohm you have a problem with nand, if you get 0.5 or near 0 ohm your gpu is shorted or burnt. From my expirience out of 10 boards i have tested if the value was below 1.5 ohm reball was needed and actualy 2 out of 10 ware burnt.

http://xbox-experts.co.uk/tutorial/how-to-understand-if-the-gpu-and-the-cpu-is-burnt/

At least you will know if it is nand or gpu.:smile:

 

[Martin C]

The problem is NOT resolved by reballing. You've damaged the CPU through trying to glitch it. I have a pile of 7 boards here from other people, ALL with the same problem. Some of you are treating the RGH like it's Lego. It's not. The soldering points are very precise and any shorts or bridges when the power is either connected or the console is turned on can have catastrophic effects. It's no coincidence the console would have been working before you started, either.

 

[SOloNon]

Hi there,

You can check if gpu needs reballor is burnt without taking the chip off.

see the link below, last picture at the bottom shows where to check and if you get around 2ohm you have a problem with nand, if you get 0.5 or near 0 ohm your gpu is shorted or burnt. From my expirience out of 10 boards i have tested if the value was below 1.5 ohm reball was needed and actualy 2 out of 10 ware burnt.

http://xbox-experts.co.uk/tutorial/how-to-understand-if-the-gpu-and-the-cpu-is-burnt/

At least you will know if it is nand or gpu.:smile:

thank you i will check .

The problem is NOT resolved by reballing. You've damaged the CPU through trying to glitch it. I have a pile of 7 boards here from other people, ALL with the same problem. Some of you are treating the RGH like it's Lego. It's not. The soldering points are very precise and any shorts or bridges when the power is either connected or the console is turned on can have catastrophic effects. It's no coincidence the console would have been working before you started, either.

Yes you right , one night i played with caps and either console's ass and i think the problem began on that night , now do you think problem may be resolve by changing the CPU ? is there any chance ?

 

[Martin C]

If you replace the CPU then yes, it will work.

For that you'd need a similar CPU which works. You obviously can't buy them separately.

 

[SOloNon]

except xenon and zypher all phat's CPU can be work , right ?

 

[Martin C]

No - for a Jasper you'd need a Jasper CPU for complete compatibility. You can use a later Falcon CPU but there's other work to be done too.

 

[SOloNon]

thank you martin ,god knows if you dont be exist we what must fcuk to do...