RGH Jasper 16 dead after write RGH

[Netkar]

Hi all, I have to do RGH jasper 16.
I used Xecuter CoolRunner, QSB and nand-x to do everything. Readed the NAND, compared 4 times it's ok so I put the xell, very well. I build glitch image with xnand of healers, I put the key that I copied from Xell, write is ok but the console is dead..... I think to rewrite nand but nandpro3 tell me "can not continue".
What to do? thanks

 

[gargoyle67]

Have you got the power cable plugged, But don't turn the 360 on ? I had this the 1st time I tried to dump my nand, The power lead from my power brick had popped out

 

[Netkar]

yes plugged, the coolrunner have the red led power on.

 

[gargoyle67]

Possible your solder connection on your QSB has gone bad when you removed the Nand-x programing wires, Check those and post some shots of your soldering.

 

[Netkar]

ok I do but you think that is possibe not have life?

Edit:images

 

[diaboliq20]

so you are getting power to the coolrunner, but the console will not boot at all after writing the glitch image?
the soldering doesn't look great on the nand-x QSB tbh, so double check that, but if it dumped and wrote ok....hmmmm.....
try writing the original NAND back

 

[Netkar]

I can't nandpro don't see

see video
http://www.youtube.com/watch?v=8e_zSZAg7aM&feature=youtu.be

 

[diaboliq20]

ok - if the coolrunner is powered, but NANDpro cannot see the NAND-X, and the console does not power, there must be a short somewhere......go over all the solder points with a magnifier, and try and see if you can get some hi res closeup pics for us to have a look at

also make sure that the USB ports are not grounding to the case

it still looks to me like that NAND-X QSB is squint, and the solder is bridging

 

[Netkar]

I think the problem is in the nand written. Is impossible that the first second all well after write, and write is ok, don't power on...
Images:

 

[chossy]

Could you measure the resistance of the resistor by the hanna chip should be 34 ohm.
I had a simular fault on a jasper where the customer had solder to the resistor and not the pad and killed the resistor.
The coolrunner would light up but the xbox would not power on.

 

[Netkar]

I'va check and it's ok..
What to do?
I think to leave all and start again with nand-x wires.
It's possible that the image or cpu key are wrong? But if is right, why don't Read nand?
Thanks 4 your support guys

 

[Martin C]

What command did you use to write the ecc image ?

 

[mamaki]

i have the same problem but with a Falcon and a Trinity, what software you use to build the glitch image? Read my post.

 

[Netkar]

I used xnand healer tool, it have Made all for me..

edit: lol I've read the topic, same tools (xnand healer 0,72 and multibuilder 0,7) only nandpro difference, I have 3.0.
What to do now?

 

[spookyman166]

ok check CPU key and Nand... Fire up 360 flash tool...

>Load Nand
>enter key

If you get all errors (like cant see CB, DVD Drive key etc) and sh*t on the right side... Key wrong.... if not well then you nand and key are good....

Also try removing QSB's... They make life harder not easier... Just flux the points, and apply heat to pre-tinned wires. Neat and tidy install...

ALWAYS USE HOT GLUE!

 

[Netkar]

thanks for support key is right I can see dvd key and all.
I think the problem is in the rgh image written and I think the problem is the software...
do you have any idea? I will leave qsb and coolrunner but I don't think is this the problem, mamaki have the same problem and with 2 console but the same software we have used. Some bugs? how can fix if we can't read/write?
many thanks boys

 

[spookyman166]

Reboot your system... I had issues with nand detection and after a pc reboot it was all goods... Take the nand x out of USB and reboot the pc... Also turn the console off for 30 seconds and press the power button a few times while the cords are out...

Replug everything and try again...

 

[frazzeld]

What dashboard are you trying to get to?
Use an older version of Multibuilder
v4 Dash: 13604
v5 Dash: 14699

flash via usb
nandflash.bin
xenon.elf

Edit: remove green wire "trim back slightly re tin and re position"

 

[Netkar]

tried to reboot many times isn't the problem.
dash 14699, xbox don't power so no xell too.

All after rgh write nand

 

[chossy]

Ok please test for continuity between the right hand side of the resistor near the hanna chip and the cool runner to see if yo have damaged the trace at all. also check for shorts on the green wire.
If no probs found remove everything carfully and examine the points for any damage and try and power the console