RGH Jasper (16mb) won't load into XELL, any ideas?

C

Craps

Full Member
Dec 1, 2011
31
0
Earth
its a Jasper 16mb (v4), just wont glitch.
I have try Coolrunner and Matrix and with the cap on GND and A.
I have flash back original nand and it boots fine with collrunner set to "pro" flash back "EccImage" to nand but no luck.

I have try the wireing like shown, but no luck on this one.

Made a falcon a few days ago and it glitch first time every time.
Just made other Jasper same version and it glitch first time with cap on GND and A, but this Jasper wont glitch at all :-(
CB is the same on both "6750" SMC "2.3"

any ideas?
 
C

Craps

Full Member
Dec 1, 2011
31
0
Earth
its the same as the picture in the wire install. the fixed one.

I have all so try to move them around with same result.

I have try to run the "D" wire on top og mainboard like i dit on the other Jasper i just made and was working i first glitch.


Ill make some pic. and upload later today.
 
C

Craps

Full Member
Dec 1, 2011
31
0
Earth
Just try to re-solder all wires with fres flux and flash back to original nand then try for 3 time to generate EccImage3.ecc and stil the same.

I have try with other Coolrunner the first i try is now in the other Japer i just made and its working, so it cant be the coolrunner, it try to glitch but stays on black screen, if i turn off coolrunner and try to boot normal i get the 0022, i gues its normal when EccImage3.ecc is in the nand and no glitch is try.

I was reading this post about 0022 but for the fix i need CPU key and i can only get this fron boot to xell.
 
C

Craps

Full Member
Dec 1, 2011
31
0
Earth
Martin C said:
You'll get 0022 from ecc without CPU_PLL_BYPASS in place, so ignore it.

Does the green light stop flashing at all?
Click to expand...

Ok that was all so what i think about the 0022.


Yes Coolrunner try to glitch like on the other i have RGH, all looks like its fine, green light comes every 3-5 sec.
 
C

Craps

Full Member
Dec 1, 2011
31
0
Earth
I have all so remove brige on efuze, its the same, and i have try to remove the efuze, its the same.

---------- Post added at 16:24 ---------- Previous post was at 16:23 ----------
Martin C said:
ok - leave JTAG Tool for now and use Multi_Builder 0.7
Click to expand...
Need cpukey else it will fail :confused:
 
C

Craps

Full Member
Dec 1, 2011
31
0
Earth
What happen if i run multi 0.7 with no cpu key in the cpukey.txt


edit: delete cpukey.txt and now i can generate ecc

Ill try the new one out, just need to flash back to original and then flash ecc, ill be back with results.
 
Last edited:
C

Craps

Full Member
Dec 1, 2011
31
0
Earth
its the same.

flash back original nand, generate ecc with 360_Multi_Builder_v0.7 and flash it with jtag tool
 
C

Craps

Full Member
Dec 1, 2011
31
0
Earth
Martin C said:
Did you definitely program the CR for Jasper?

also , try setting the CR to slim.
Click to expand...

Yes CR is made for Jasper, i try other CR and it glitch fine in other Jasper.


If i set it to slim Green led dont light up only read all the time.

---------- Post added at 17:03 ---------- Previous post was at 17:00 ----------

i can try one more CR and program it to Jasper, just dont have more time to day, ill be back tomorrow when i have try other CR with fresh programing to Jasper.
 
You must log in or register to reply here.