RGH Jasper BB 512MB~ 6751 Won't Glitch and CR Green Light doesn't Flashes

W

watkmogi

Junior Member
Dec 30, 2011
18
0
I've tried everything w/o any lucky.

I got 2 CR here, tried with both and nothing. When I put the stock nand back the console boot perfectly with CR soldered on board and the switch @ PROG.

Also i had those problems while reading nand to compare. But i heard that the ecc block were 1~50, if no bb on those the xel would boot perfectly so I'm looking for something else.

NandPro v3.0a by Tiros

Looking for usb interface device
Incompatible ARM firmware for this version of NandPro!
Flash Config: 0x00AA3020
Block Size: 128KB Block Limits: 0x000000..0x007FFF
File: Nand.bin
Reading
Error: 250 reading block 110
Error: 210 reading block 111
Error: 210 reading block 112
Error: 210 reading block 113
Error: 210 reading block 114
Error: 210 reading block 115
Error: 210 reading block 116
Error: 210 reading block 117
Error: 250 reading block 1C00
Error: 250 reading block 2110
Error: 250 reading block 48E8
Error: 250 reading block 6290
7FFF
Pressione qualquer tecla para continuar. . .
Click to expand...
...

360 Flash Dump Tool

Note: Bad Block ID 0x0022 [Offset: 0x00462000]
-> Bad Block ID 0x0022 found @ 0x01FF [Offset: 0x041DF000]

===== Analized Successfully ==========================
Click to expand...
When I power up the CR, I get the red light on and the green light don't even flash 1 time, and i've tried with 2 CR boards both programmed with jasper.jed on Impact programed and verified.

Wires: Resoldered all points and checked for continuity, all good too.

PS: I'm using the cap. that comes with the CR board, 68nf.

Any idea of what is going on?

Thanks anyway~
 
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
acording to flash dump tool you have a bad block on adress 22 have you remaped that one before writing the ecc to flash ?
 
W

watkmogi

Junior Member
Dec 30, 2011
18
0
Tried create the .ECC with Jtag tools, Multi Builder all v.0.3~0.5, python, bestpig all those programs and nothing, tried using the 512mb dump and the 64mb dump stock to make the .ECC nothing too. The xbox's green light flashs after 5~7 secs then stops for about 1,5 secs then flashs again. Sometimes the xbox's green light don't even flashs.

---------- Post added at 10:04 ---------- Previous post was at 10:03 ----------
Hackerjac said:
acording to flash dump tool you have a bad block on adress 22 have you remaped that one before writing the ecc to flash ?
Click to expand...
No, I didnt...

---------- Post added at 10:04 ---------- Previous post was at 10:04 ----------
Hackerjac said:
acording to flash dump tool you have a bad block on adress 22 have you remaped that one before writing the ecc to flash ?
Click to expand...
No I didn't, maybe thats why then ?
 
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
yes you need to remap that block manualy, there is a tut in here where it explain how to do it, can't remember where but will look for it
 
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
W

watkmogi

Junior Member
Dec 30, 2011
18
0
cfull1 said:
Are you sure stby_clk (orange) is soldered in the right spot?
Click to expand...
Dude, I'd say I love you, how could I forget about that, looked @ it a lot of times and didn't realised, gonna sold it on the right point then post again...
 
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
when you have soldered the orange wire to the right pad, flash your org nand back, set the cr to nor and phat, then see if the console then boots
 
C

cfull1

VIP Member
Mar 10, 2011
156
0
Texas!!
Yeah if I were you I'd skip that pad, I always go straight to the alternate point. It's so much easier to solder. Did you manually remap block 22?
 
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
if you flash back your org nand now, does the console then boot ?
 
W

watkmogi

Junior Member
Dec 30, 2011
18
0
Martin C said:
If you want help bud, you'll need to get better pics of your soldering. Right now I'd say CPU_PLL_BYPASS is the problem.
Click to expand...
The CPU_PLL_BYPASS is really fine soldered, can't get better pics right now, forgot my cam @ work. The console boots fine with stock nand.
 
Hackerjac

Hackerjac

The Minifigure
Staff member
Troll Eating Dogs
Jun 2, 2010
1,332
108
Denmark
as i mentioned before, acording to flash dump tool you have a bad block on adress 22, that one you need to manualy remap, i also postet a link to Martin's great guide
 
W

watkmogi

Junior Member
Dec 30, 2011
18
0
Hackerjac said:
as i mentioned before, acording to flash dump tool you have a bad block on adress 22, that one you need to manualy remap, i also postet a link to Martin's great guide
Click to expand...
I think I need to do that, cuz I just got the Xell running and got the cpu key, made the nandflasher.bin flashed on console while flashing rawflash showed a lot of erros (bad blocks) but finished. When I turn the console on the hacked dashboard freezes on xbox logo... Any idea... or that means i need to remap the bad blocks and which program do i need to use to do that?
 
W

watkmogi

Junior Member
Dec 30, 2011
18
0
dantok said:
I remember that problem. MultiBuilder helps you remap all that. If you remapped it in the beginning for xell, you need to unmap it before building the freeboot image with MultiBuilder, or it will crash at the video boot up.
Click to expand...
Just tried that and got the same errors on rawflasher
 
You must log in or register to reply here.