[Jasper] CR4 XL Wont Glitch

jparmyguy · Aug 19, 2015

Console Type: Jasper
Programmer Used: NAND-X,

NAND Size: 16
Dashboard version: 2.0.17150
CB Version: 6754
J-Runner log

Code:

J-Runner v0.3 Beta (7) Started



WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button




Checking Files
Finished Checking Files
Glitch2 Selected
CR4 Selected
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Comparing...
Bad Block ID  025F Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 025F [Offset: 0x9C7E00]
Bad Blocks Remapped
Bad Block ID  025F Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 025F [Offset: 0x9C7E00]
Bad Blocks Remapped
Nands are the same
Device Not Found.
Comparing...
Bad Block ID  025F Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 025F [Offset: 0x9C7E00]
Bad Blocks Remapped
Bad Block ID  025F Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 025F [Offset: 0x9C7E00]
Bad Blocks Remapped
Nands are the same
Glitch2 Selected
Jasper 16MB Manually Selected
ECC created
Jasper 16MB Manually Selected
ECC created
Comparing...
Bad Block ID  025F Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 025F [Offset: 0x9C7E00]
Bad Blocks Remapped
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Comparing...
Bad Block ID  025F Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 025F [Offset: 0x9C7E00]
Bad Blocks Remapped
Bad Block ID  025F Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 025F [Offset: 0x9C7E00]
Bad Blocks Remapped
Nands are the same
Glitch2 Selected
Jasper 16MB Manually Selected
ECC created
Version: 01
Flash Config: 0x00023010
Writing Nand
image_00000000.ecc
Done!
in 0:09 min:sec

Was the console working before you started: Y
Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: Y
How long is the light on for each time a split Second

My Cr4 Xl just wont glitch the console, I could leave it on for 20 minutes and it will just keep cycling in never glitch. I did previously try to install as an rjtag but ripped of alt cpu reset point, R8C2 resistor. So i deiced to re wire as RGH 2.0. Im not sure if me ripping that would make it unable to glitch but the console will still boot into stock.

playingmax · Aug 19, 2015

qsb not making contact. add more flux and retouch points.

- - - Updated - - -

also try diff DIP setting
http://team-xecuter.com/forums/threads/148002-CR4-XL-PHAT-Opus-Falcon-Jasper-Install-Guide-(RGH2-)

jparmyguy · Aug 19, 2015

playingmax said:
qsb not making contact. add more flux and retouch points.

- - - Updated - - -

also try diff DIP setting
http://team-xecuter.com/forums/threads/148002-CR4-XL-PHAT-Opus-Falcon-Jasper-Install-Guide-(RGH2-)

Both Pads? Would that effect it glitching at all?

playingmax · Aug 19, 2015

jparmyguy said:
Both Pads? Would that effect it glitching at all?

yes it would. also from the pics looks like all dips are off. and trim your wires.

jparmyguy · Aug 19, 2015

playingmax said:
yes it would. also from the pics looks like all dips are off. and trim your wires.

It's just the angle of the camera, I have tried about 4 different dip settings, what wire should be trims and by how much?

GeekHeat · Aug 19, 2015

jparmyguy said:
It's just the angle of the camera, I have tried about 4 different dip settings, what wire should be trims and by how much?

There are about 15 different dip settings to try and 3 postbit jumpers settings.

jparmyguy · Aug 19, 2015

GeekHeat said:
There are about 15 different dip settings to try and 3 postbit jumpers settings.

I'll keep on trying different settings when I get home from work, if that doesn't work?

jparmyguy · Aug 20, 2015

GeekHeat said:
There are about 15 different dip settings to try and 3 postbit jumpers settings.

Ok So I have tried every possible combo and it wont glitch it just keeps cycling for however long i leave it on for..[video=youtube;U4ft0zFDjLQ]https://www.youtube.com/watch?v=U4ft0zFDjLQ[/video]

Nintendo · Aug 20, 2015

jparmyguy said:
Ok So I have tried every possible combo and it wont glitch it just keeps cycling for however long i leave it on for..[video=youtube;U4ft0zFDjLQ]https://www.youtube.com/watch?v=U4ft0zFDjLQ[/video]

Solder again cpu rst on both sides, let the solder flow. That point is critical. Is cut to size? And POST?

jparmyguy · Aug 20, 2015

Nintendo said:
Solder again cpu rst on both sides, let the solder flow. That point is critical. Is cut to size? And POST?

Well I decided to try and switch to double shielded cable like i tried on the alt cpu reset point and it ripped off pad just like the resistor. So sh*t out of luck now. Out of curiosity can you explain cut to size. Its been a while since i fooled around with this stuff. I have succecfuly jtaged xbox before with rjtag chip but not this cr4 i have encountered numerous issues.
Edit: Point actually did not rip off thankfully

jparmyguy · Aug 20, 2015

This Resitior that I pulled, I wonder if it is causing the issue?

Nintendo · Aug 20, 2015

jparmyguy said:
Well I decided to try and switch to double shielded cable like i tried on the alt cpu reset point and it ripped off pad just like the resistor. So sh*t out of luck now. Out of curiosity can you explain cut to size. Its been a while since i fooled around with this stuff. I have succecfuly jtaged xbox before with rjtag chip but not this cr4 i have encountered numerous issues.
Edit: Point actually did not rip off thankfully

I just use that wire with a QSB or using some hot glue, if not it's very dangerous.

I meant that the wires should be cut just to fit. With CR4XL, the less wire, the best.

That 1K resistor is not needed, unless you want to use that point again.

jparmyguy · Aug 20, 2015

Nintendo said:
I just use that wire with a QSB or using some hot glue, if not it's very dangerous.

I meant that the wires should be cut just to fit. With CR4XL, the less wire, the best.

That 1K resistor is not needed, unless you want to use that point again.

So do you think the problem could be the bad block or am I missing a step in flashing the ecc?
Edit: I also decided to throw on a 22 cap? Im hot gluing wire so it doesn't rip again and permanently screw the xbox..

jparmyguy · Aug 20, 2015

There also been an issue where i tired to put the stock nand back on the xbox after blocks were remapped and it fails to write remapped block?

Nintendo · Aug 20, 2015

jparmyguy said:
So do you think the problem could be the bad block or am I missing a step in flashing the ecc?
Edit: I also decided to throw on a 22 cap? Im hot gluing wire so it doesn't rip again and permanently screw the xbox..

But what CPU_Rst point are you using right now?

jparmyguy said:
There also been an issue where i tired to put the stock nand back on the xbox after blocks were remapped and it fails to write remapped block?

Where is the badblock ? If it is just one I assume it's not a problem. It boots stock?

jparmyguy · Aug 21, 2015

Nintendo said:
But what CPU_Rst point are you using right now?

Where is the badblock ? If it is just one I assume it's not a problem. It boots stock?

I am using the underside point that begins with a C not the resistor i ripped. It is block 25F and when i put the dump back on the xbox it did boot stock. One thing i notice was i was unable to update dash via live.

Nintendo · Aug 21, 2015

jparmyguy said:
I am using the underside point that begins with a C not the resistor i ripped. It is block 25F and when i put the dump back on the xbox it did boot stock. One thing i notice was i was unable to update dash via live.

Be careful there, keep your Nand Dumps organized. Just a single block is nothing to worry about. Why are you unable to do that? If it boots, that's because your board is fine.

jparmyguy · Aug 21, 2015

Nintendo said:
Be careful there, keep your Nand Dumps organized. Just a single block is nothing to worry about. Why are you unable to do that? If it boots, that's because your board is fine.

It just gave me an error code even though it connected to live I was able to update it from flash drive though and re did the whole process still a bad block though..I am wondering what the problem is, this is the second Xbox that has been a failure

jparmyguy · Aug 21, 2015

The only difference from this double shielded cable is the fan no longer makes the noise

Nintendo · Aug 21, 2015

jparmyguy said:
The only difference from this double shielded cable is the fan no longer makes the noise

The reset noise? Repair the trace.

Search

Search

[Jasper] CR4 XL Wont Glitch

jparmyguy

Full Member

playingmax

jparmyguy

Full Member

playingmax

jparmyguy

Full Member

GeekHeat

jparmyguy

Full Member

jparmyguy

Full Member

Nintendo

jparmyguy

Full Member

jparmyguy

Full Member

Nintendo

jparmyguy

Full Member

jparmyguy

Full Member

Nintendo

jparmyguy

Full Member

Nintendo

jparmyguy

Full Member

jparmyguy

Full Member

Nintendo