Jasper not glitching in to Xell , need some help

[s8n187]

hi TX members , this is my second attempt at modding a 360 the first one came out great thanks to members here.


with this Jasper 360 i cant boot into XELL and get the CPU Key , interestingly with the green pulses from the CR4 i get 1 pulse then about 5 seconds later i get 2 then 5 seconds later 1 then 5 seconds after that 3 pulses sort of behaviour.



i also made a mistake when i first fired on the 360 to boot into XELL , i forgot to bridge 1 and 3 on the QSB but that has been fixed although i still cant get into XELL.

• Console Type: Jasper
• Programmer Used: JRP v2.0
• NAND Size: 16MB
• Dashboard version: 16747
• CB Version: 6754

Was the console working before you started: Yes

Do you get a green debug light appear on the CR4 XL chip every 4-5 seconds: yes

Wednesday, March 11, 2015 6:59:48 AM

J-Runner v0.3 Beta (7) Started



Checking Files
Finished Checking Files
Jtag Selected
Aud_Clamp Selected
R-Jtag Selected
R-Jtag de-Selected
Aud_Clamp de-Selected
Retail Selected
Checking Console..
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Reading Nand to C:\downloads\output\nanddump1.bin
Reading Nand
Done!
in 3:25 min:sec

Reading Nand to C:\downloads\output\nanddump2.bin
Initializing nanddump1.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
Reading Nand
Done!
in 3:25 min:sec

Comparing...
Nands are the same

===================================================
Wednesday, March 11, 2015 7:26:07 AM

J-Runner v0.3 Beta (7) Started



Checking Files
Finished Checking Files
Jtag Selected
Aud_Clamp Selected
R-Jtag Selected
Checking Console..
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 6754
Jasper 16MB
Reading Nand to C:\downloads\output\nanddump1.bin
Reading Nand
Done!
in 3:25 min:sec

Reading Nand to C:\downloads\output\nanddump2.bin
Initializing nanddump1.bin..
Jasper 16MB
Nand Initialization Finished
Reading Nand
Done!
in 3:25 min:sec

Comparing...
Nands are the same
Patching Jasper version 2.3 SMC at offset 0x12BA
XeLL file created Successfully jasper_hack_aud_clamp.bin
Version: 10
Flash Config: 0x00023010
Writing Nand
jasper_hack_aud_clamp.bin
Done!
in 0:17 min:sec

 

[john mathews]

I would try different posftbit / and dips starting with 3 and so one til u find that sweet spot /u have jrp v2 so u can check rater

 

[h1n1viruz]

Check wire placement of the cpu_rst (blue) make sure it's not placed directly under the Hana chip,and move towards the center of the board, but secure the wire first before moving it don't wanna pull off a pad and just make sure all points look nice and shiny, retouch solder if it needs to be, I have a jasper I just rjtag

 

[s8n187]

hi guys im back with some crazy news...................



the blue wire was running directly under the Hana so i moved it as h1n1viruz suggested and fired up the 360 , Xell booted !!



absolutely stoked , also id like to learn more about the Rater as John mentioned so i can get better glitch times i plan on doing more 360's for myself

 

[briggs01]

check the point at the end of the QSB , R4B24 it doesn't look soldered on the pic

 

[h1n1viruz]

I play with the jumper settings and dips and the jtag qsb, I tend to get better boot times with it in the middle 100Ohms on cr4, and jtag qsb set to 330, I haven't had the tater set up as I'm still learning bout the mods, I plan to get a trinity and use my other cr4, but I find this to be real fun to do,
my boot times are 7-8sec with one glitch, and if you get freezing issues it can still be the blue wire as I ran into those issues and moved the wire more good luck! And glad I was able to help you ��

 

[s8n187]

thanks John , briggs and h1n1viruz for everything all is going great so far ive played a few games totaling about 41 mins no problems


thanks for the support and tips it is much appreciated


DEAN

 

[clarcks]

h1n1viruz;1041299]I play with the jumper settings and dips and the jtag qsb, I tend to get better boot times with it in the middle 100Ohms on cr4, and jtag qsb set to 330, I haven't had the tater set up as I'm still learning bout the mods, I plan to get a trinity and use my other cr4, but I find this to be real fun to do,
my boot times are 7-8sec with one glitch, and if you get freezing issues it can still be the blue wire as I ran into those issues and moved the wire more good luck! And glad I

 

[keil423]

check the point at the end of the QSB , R4B24 it doesn't look soldered on the pic

That point at the end no longer needs to be solder. It has also been the cause of a lot of trouble for new installers. Terrible little resistor to mess up!

 

[dayveed]

Isn't R4B24 the STBY_CLK? He's doing a RJTAG so that does need to be soldered, no?

 

[john mathews]

yes on trinity/ if hes using cr4 no its not used but for a reg coolrunner without oscillator then yes its used

 

[keil423]

With the cr4 the stby clk does not need to be soldered. That's on the end of the nand qsb. The point on the end of the aid clamp qsb also does not need to be soldered to that resistor.

 

[dayveed]

Doesn't that mean that the B point on the CR4 isn't connected to anything on the board? Is the wire connected to the B point on the CR4 unnecessary?