I purchase the R-Jtag starter kit which doesn't included the Nand-X QSB, what are the solder points for 5v, D, B, E, F, and K? I couldn't find any picture or diagram on the forums.
Thanks.
Thanks.
Jasper R-JTAG Problem
- Thread starter factistrue
- Start date
BL4K3Y
VIP Member
Re: R-Jtag solder points
Console Type: Jasper
NAND size: 16
Dashboard version: 2.0.14719
CB version: 6754
POST output from J-Runner (either POST_OUT monitor or RATER output):
Phat Selected
Version: 10
Power Up
Waiting for POST to change
Post E0
Post A0 - Panic - VERIFY_SECOTP_6
Post 80
Image of R-JTAG board:
Images of close-up soldering to motherboard:
Description of problem:
Was the console working before you started: Y
When I run Rater though I immediately get Post A0 - Panic - VERIFY_SECOTP_6.
Any help?
Console Type: Jasper
NAND size: 16
Dashboard version: 2.0.14719
CB version: 6754
POST output from J-Runner (either POST_OUT monitor or RATER output):
Phat Selected
Version: 10
Power Up
Waiting for POST to change
Post E0
Post A0 - Panic - VERIFY_SECOTP_6
Post 80
Image of R-JTAG board:
Images of close-up soldering to motherboard:
Description of problem:
Was the console working before you started: Y
When I run Rater though I immediately get Post A0 - Panic - VERIFY_SECOTP_6.
Any help?
Last edited:
BL4K3Y
VIP Member
Re: R-Jtag solder points
Completing the template with pics would help read this it is Ubergeeks install guide also talks about about fails etc. Short paragraph below
Full fail = 0xA0 as last post
0x21 or 0x22 or 0x87 as last post means that all checks were passed but something went wrong, possibly glitch timing wrong or too deep
If u get all 0xA0 on any dips then install is wrong, like cpu_rst or E/F is badly soldered
If you get 0x21, this usually means you are 1 DIP past optimal e.g DIP 4 gives 21-22 and DIP 5 gives 21.
Sometimes it will fail on 0x2E - this is way down on the boot cycle. This generally points to bad wiring or that an RROD is on the way and a reflow may be required or ideally a reball, specifically on the CPU.
Completing the template with pics would help read this it is Ubergeeks install guide also talks about about fails etc. Short paragraph below
Full fail = 0xA0 as last post
0x21 or 0x22 or 0x87 as last post means that all checks were passed but something went wrong, possibly glitch timing wrong or too deep
If u get all 0xA0 on any dips then install is wrong, like cpu_rst or E/F is badly soldered
If you get 0x21, this usually means you are 1 DIP past optimal e.g DIP 4 gives 21-22 and DIP 5 gives 21.
Sometimes it will fail on 0x2E - this is way down on the boot cycle. This generally points to bad wiring or that an RROD is on the way and a reflow may be required or ideally a reball, specifically on the CPU.
Re: R-Jtag solder points
Version: 10
Power Up
Waiting for POST to change
Post E0
Post A0 - Panic - VERIFY_SECOTP_6
Post 80
Image of R-JTAG board:
Images of close-up soldering to motherboard:
Description of problem:
Was the console working before you started: Y
When I run Rater though I immediately get Post A0 - Panic - VERIFY_SECOTP_6.
Any help?
Console Type: Jasper
NAND size: 16
Dashboard version: 2.0.14719
CB version: 6754
POST output from J-Runner (either POST_OUT monitor or RATER output):
Phat SelectedNAND size: 16
Dashboard version: 2.0.14719
CB version: 6754
POST output from J-Runner (either POST_OUT monitor or RATER output):
Version: 10
Power Up
Waiting for POST to change
Post E0
Post A0 - Panic - VERIFY_SECOTP_6
Post 80
Image of R-JTAG board:
Images of close-up soldering to motherboard:
Description of problem:
Was the console working before you started: Y
When I run Rater though I immediately get Post A0 - Panic - VERIFY_SECOTP_6.
Any help?
Martin C
VIP Member
Re: R-Jtag solder points
Does the console still boot a stock NAND if you desolder D, E and F from the R-JTAG?
If so, run RATER with these wires removed (and on stock NAND) and see what output you get.
EDIT: this won't work on the newer dashboards, sorry.
Does the console still boot a stock NAND if you desolder D, E and F from the R-JTAG?
If so, run RATER with these wires removed (and on stock NAND) and see what output you get.
EDIT: this won't work on the newer dashboards, sorry.
Taijigamer2
VIP Member
Martin C
VIP Member
Re: R-Jtag solder points
Well spotted.
OP - you'll need to update to at least 15572 (as this is when the new bootloaders were released).
Just take it to 16537.
Well spotted.
OP - you'll need to update to at least 15572 (as this is when the new bootloaders were released).
Just take it to 16537.
Re: R-Jtag solder points
Alright, how would I go about updating the dash to 16537 since the console has 3RROD on boot? I load the original NAND back from backup but it still gets 3RROD.
Antalpromille
VIP Member
Re: R-Jtag solder points
Yes the 5V goes from the R-Jtag 1.1 chip to the mb's solder point
R-Jtag solder points
Tapatalk misspelled it. Knot me.
Does that mean its disconnected or still connected? It needs to be disconnected when trying to boot stock.
Tapatalk misspelled it. Knot me.
Last edited:
Re: R-Jtag solder points
Okay I updated the system to the latest dash, and re-soldered everything perfectly. For some reason on J-Runner I still get under Nand Info after reading the Nand 4 times:
6BL [CF] 14699 6BL[CF] Patch 1 16537
7BL [CG] 14699 7BL [CG] Patch 1 16537
even after upgraded the system to the latest dash as stated above. Is this correct?
Okay I updated the system to the latest dash, and re-soldered everything perfectly. For some reason on J-Runner I still get under Nand Info after reading the Nand 4 times:
6BL [CF] 14699 6BL[CF] Patch 1 16537
7BL [CG] 14699 7BL [CG] Patch 1 16537
even after upgraded the system to the latest dash as stated above. Is this correct?
BL4K3Y
VIP Member
Re: R-Jtag solder points
That is telling you that the dashboard version was updated from 14699 to 16537.
That's fine.
That is telling you that the dashboard version was updated from 14699 to 16537.
Re: R-Jtag solder points
Create Xell-Reloaded, Write Xell-Reloaded, Dips 7,8, 5 on and it won't boot to Xell
Also tried several dip settings, and jumper settings. It still wont glitch.
Okay thanks, I checked the Aud_Clamp option and R-Jtag option.
Create Xell-Reloaded, Write Xell-Reloaded, Dips 7,8, 5 on and it won't boot to Xell
Also tried several dip settings, and jumper settings. It still wont glitch.
Last edited:
Re: R-Jtag solder points
Post rater log with stock nand by disconnecting d, e, and f wires, flash back to stock, boot with rater, post log. also this error usually around d, e, f wires.
Post rater log with stock nand by disconnecting d, e, and f wires, flash back to stock, boot with rater, post log. also this error usually around d, e, f wires.
BL4K3Y
VIP Member
Re: R-Jtag solder points
You also have the AUD_CLAMP wire soldered to the wrong spot:
Post a new RATER log please (three cycles should be enough).
You also have the AUD_CLAMP wire soldered to the wrong spot:
Last edited: