Jasper R-JTAG Stopped Booting

[Ressko]

So a few weeks ago I r-jtagged my jasper and everything went well, no problems. 2 Days ago my was playing around with my cod ghosts XRPC tool... I was experimenting with some offsets and my xbox kept freezing because the offsets weren't right. I had to press the power button twice to turn the console off... after a few times of doing this my console stopped booting dash and xell, I opened it up and when i powered the console on the r-jtag chip the DBG light would flash once and no more... I thought maybe the chip was faulty so I fitted a spare and I also used a new post out wire. The console still would not boot, I removed the chip and reflashed the nand back to stock and the console booted fine. Im not sure why it wont boot, im completely confused... also now the chip flashes green a few times but eventually stops and dosent boot. any help if appreciated.

Here are some install photos and info:


Console Type: Jasper
NAND size: 16
Dashboard version: the latest
CB version: not sure (can check)
Screenshot of NAND details from J-Runner: http://gyazo.com/c11424a518e5a3bcb7a930669b1b9706
(attach an image to your post)

J-Runner log:J-Runner v0.3 Beta (2) Started




It's advised to run in administrator mode on Windows 8
WARNING! - Your selected working directory already contains files!
You can view these files by using 'Show Working Folder' Button




Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Falcon/Opus
RGH Selected
Nand Initialization Finished
Initializing updflash.bin..
Jasper 16MB
Jtag Selected
Nand Initialization Finished
R-Jtag Selected
Version: 03
Flash Config: 0x00023010
Writing Nand
updflash.bin
Error: 202 writing block 2A7
Done!
in 2:03 min:sec



Image of R-JTAG board:

Close up images of soldering: Pic1 Pic2 Pic3 Pic4 Pic5 Pic6


If i need better images please let me know and I will try.

 

[Martin C]

Where's your POST output?

 

[Ressko]

Where's your POST output?

I only got the standard kit and I dont have a JRP, just a NAND-X.

 

[Martin C]

There's very little anyone can advise you. The standard kit is for people who have a J-RP v2 already.

 

[Ressko]

There's very little anyone can advise you. The standard kit is for people who have a J-RP v2 already.

How much would you charge for a "repair", to restore it to working order?
It would probbably be easier to send it to Bl4key as I am in the north west as he is.

 

[Martin C]

How much would you charge for a "repair", to restore it to working order?
It would probbably be easier to send it to Bl4key as I am in the north west as he is.

It all depends what's wrong with it. Repairs start from £30.

 

[XMonsterModsX]

cod ghosts XRPC tool :facepalm: call of duty ghost hasnt been released yet

 

[Antalpromille]

You say its a Jasper, you have your R-jtag setup for Jasper (dip 7-8 on) but jrunner reports that its a Falcon/Opus. Are you confused?

Also the game you was playing around it is released tomorrow.

 

[Ressko]

It all depends what's wrong with it. Repairs start from £30.

So if i got a JRP and used the rater feture I would have a good chance of seeing whats wrong with it?

And yea, ghosts is released tommorow but I have a leaked version? lol

 

[Ressko]

You say its a Jasper, you have your R-jtag setup for Jasper (dip 7-8 on) but jrunner reports that its a Falcon/Opus. Are you confused?

Also the game you was playing around it is released tomorrow.

Its a jasper lol... Look in the jrunner nand info screenshot :/

 

[Martin C]

Of course - that's what the RATER is for.

 

[Antalpromille]

Its a jasper lol... Look in the jrunner nand info screenshot :/

Ah i see that now, i was only lookin at the log and your nanddump1.bin reported as a Falcon/Opus.

 

[Ressko]

Of course - that's what the RATER is for.

Ok, well I shall get one... What could possibly be wrong with it? Like would bit be a hardware error or image error chip error? Please give an example of what it could be.


Thanks

 

[Antalpromille]

Ok, well I shall get one... What could possibly be wrong with it? Like would bit be a hardware error or image error chip error? Please give an example of what it could be.


Thanks

Since you tried two different chips then you have damaged your motherboard or a bad install.

 

[Ressko]

Also, I know with r-jtags the RF board plays up sometimes but now whenever I try to boot it the rf board always goes crazy? could that explain anything?

 

[Antalpromille]

Also, I know with r-jtags the RF board plays up sometimes but now whenever I try to boot it the rf board always goes crazy? could that explain anything?

It does this if you dont use aud_clamp option.

 

[Ressko]

It does this if you dont use aud_clamp option.

Ahh, ok thanks

 

[Antalpromille]

Ahh, ok thanks

No problem. It doesnt do it all times but pretty random

 

[Ressko]

Since you tried two different chips then you have damaged your motherboard or a bad install.

Well you tell me if its a bad install? it was working good, im a relitavley good solderer, ive done over 25 consoles and rarely have a problem.... Also the console boots fine do stock so I dont think it is the motherboard that is a problem... Im just really confused with this one.

 

[Antalpromille]

Well you tell me if its a bad install? it was working good, im a relitavley good solderer, ive done over 25 consoles and rarely have a problem.... Also the console boots fine do stock so I dont think it is the motherboard that is a problem... Im just really confused with this one.

Untill there are better clearer pictures of your install its hard to say, but what i do know is that a bad install can work for a while. I also know theres a very small chance that your chip died and that the replacement also was faulty. Not all solder spots are critical for booting your stock nand. I can also tell from the picture of your chip that you are using too much solder on the solderpoints.